Adj WiFLY QA5 IP handleiding
Handleiding
Je bekijkt pagina 8 van 16
ADJ Products, LLC - www.adj.com - WiFly QA5 IP User Manual Page 15ADJ Products, LLC - www.adj.com - WiFly QA5 IP User Manual Page 14
WiFly QA5 IP Master-Slave Configuration
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-
Slave mode. In a Master-Slave set up one unit will act as the control-
ling unit and the others will react to the controlling units built-in pro-
grams. Any unit can act as a Master or as a Slave however, only one
unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR data cables to link your units together.
Remember that the Male XLR connector is the input and the
Female XLR connector is the ouput. The first unit in the chain
(master) will use the female XLR connector only. The last unit in
the chain will use the male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. On the “Slave” units press the MODE button until “SLAu” is dis-
played. The unit is now set as the “Slave” unit. Each slave unit
must be set to the same setting.
4. Connect the rst “Slave” unit to the “Master”, and the “Slave” unit
should now start follow the “Master”.
WiFly QA5 IP WiFly Set Up
WiFly QA5 IP WiFly Master-Slave Set Up
With this feature you are able to control the unit with DMX without the
need of XLR cables. Your DMX controller must be connected to a ADJ
WiFly TransCeiver to use this function. You are able to communicate
up to 2500 feet/760 meters (open line of sight).
NOTE: The ADJ RFC control must be set to OFF to use this func-
tion. See page 12 to turn OFF ADJ RFC.
1. Turn on the WiFly function using the instructions on pages 12-13.
2. Follow the instructions on page 13 to set the Wireless address.
The address must match the address set on the WiFly Transceiver.
3. After you have set the WiFly address, follow the DMX instructions
on pages 11-12 to select your desired DMX Channel mode and
set your DMX address.
4. Apply power to the ADJ WiFly Transceiver. The fixture must be set
up first before you apply power to WiFly Transceiver.
Note: If the sync does not work, switch the WiFly power off then on
again.
This feature will let you link units to run in a master-slave mode with-
out the use of XLR cables.
NOTE: The ADJ RFC control must be set to OFF on all the units
to use this function. See page 12 to turn OFF ADJ RFC.
1. Follow the instructions on page 13 to set the Wireless address.
The addresses on each fixture must be the same.
2. After you have set the WiFly address, select your master unit and
set your desired operating mode.
3. Turn on the WiFly function using the instructions on pages 12-13.
4. For the Slave units, put the unit in Slave mode. See page 14
Master-Slave configuration when setting the unit as a Slave. Then
switch ON the WiFly power.
NOTE: If they do not sync up master-slave, switch the Master fix-
tures WiFly off then on again.
Bekijk gratis de handleiding van Adj WiFLY QA5 IP, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Adj |
| Model | WiFLY QA5 IP |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2651 MB |
