Adj Vizi Scan LED Pro handleiding

Niet gecategoriseerd

Adj

26 pagina's

PDF beschikbaar

Handleiding

American DJ® - www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 28American DJ® - www.americandj.com - Vizi Scan LED PRO Instruction Manual Page 27

Vizi Scan LED PRO System Menu

3. Tap the UP button until “SPOT” is displayed, press ENTER.

4. The display will show “ON/OFF”.

5. Press the UP button to select “ON” to activate this function,

or “OFF” to deactivate this function.

6. Press ENTER to conrm.

7. Press MODE/ESC to return to the main menu.

DFSE - With this function you can restore the factory

settings of the device. All settings will be set back to the

default values. Any edited scenes will be lost. When restor-

ing the factory settings the unit must be set to the address

that the unit was in when you started editing.

1. Access the main menu.

2. Tap the UP button until “SPEC” is displayed, press ENTER.

3. Tap the UP button until “DFSE” is displayed, press ENTER.

4. The display will show “ON/OFF”.

5. Press the UP button to display “ON” to activate this function,

or “OFF” to deactivate this function.

6. Press ENTER to conrm.

7. Press MODE/ESC to return to the main menu.

When you exit this function, the unit will begin to reload

data.

FANS - With this function you can choose between the fan

settings of Low, High or Auto. The default setting is Auto.

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “FANS” is displayed, press ENTER.

3. Press the UP or DOWN buttons to select either “LOW”, “HIGH”,

Vizi Scan LED PRO System Menu

5. Press ENTER to conrm, and “PASS” will ash quickly.

6. Press MODE/ESC to return to the main menu.

To use this function follow the instructions:

To adjust the address of your unit you must rst go to the

address that it is currently set to. From there you can adjust the

address. First make sure all channels are set to the value of “0”.

1. On your DMX controller set the DMX value of Channel 1 to

the value “7”.

2. Now set the DMX value of Channel 2 to the value “7” to

adjust the starting address between 1 and 255. To adjust the

address between 256 and 511 set Channel 2 to the value “8” .

3. Set the DMX value of Channel 3 to your desired start-

ing address. This will take about 20 seconds before the unit

accepts the new DMX address.

EXAMPLE: So, if you want the address to be 57, you must rst

set the address that is currently assingned to the unit. The pro-

ceed to set Channel 1s’ value to “7”, Channel 2s’ value to “7”,

and Channel 3s’ value to “57”.

2ND EXAMPLE: Again, if you want the address to be 420, you

must rst set the address that is currently assingned to the unit.

If you want the set the address to 420, set Channel 1s’ value to

“7”, Channel 2s’ value to “8”, and Channel 3s to “164”. (256 +

164 = 420)

SPOT - With this function you can adjust the LED optimi-

zation via the control board. The shutter opens and the LED

can be adjusted. In this mode, the device will not react to

any control signal.

1. Access the main menu.

2. Tap the UP button until “SPEC” is displayed, press ENTER.

Bekijk gratis de handleiding van Adj Vizi Scan LED Pro, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.