Zoom RFX-2000 handleiding
Handleiding
Je bekijkt pagina 24 van 28
24
ZOOM RFX-2000
Supplied Software / Troubleshooting
Troubleshooting
No sound or very low
volume
• Is supplied AC adapter connected correctly?
Follow the instructions in "Getting Connected".
Use only the supplied AC adapter.
• Is another kind of AC adapter connected?
• Is sound source connected correctly to
INPUT jacks and are OUTPUT jacks
connected correctly to playback system?
Follow the instructions in "Getting Connected".
• Is a microphone connected to the rear-
panel INPUT jack?
Connect the microphone to the front-panel MIC
IN jack.
• Is unit in bypass mode and is MIX control
fully turned to the WET position?
Turn MIX control towards DRY.
• Is EDIT control knob 1 - 4 set to a position
where sound is cut off?
Turn EDIT control knob 1 - 4 clockwise.
• Are all shielded cables used for the
connection okay?
Try replacing the shielded cables.
Adjust the controls as described in the section
"Trying Out the Effects".
• Are the connected sound source and
playback system operating normally? Is the
volume set to a proper position?
• Are INPUT and OUTPUT controls of RFX-
2000 set to a proper position?
Check all components and set the volume to a
suitable position.
Input sound breaks up
or is distorted
• Is input signal level too high?
Adjust INPUT control so that CLIP LED does
not light at signal peaks.
No effect sound
• Is incorrect foot switch connected?
Use only ZOOM FS01.
• Is RFX-2000 set to bypass mode?
Cancel the bypass mode.
Symptom Check Remedy
The RFX-2000 comes with a CD-ROM that contains software
for editing patches on a personal computer. (The disc contains
versions for Windows 95/98 and Macintosh.) The software
comprises the following functions.
(1) Patch librarian
Serves to manage patch information of the RFX-2000 on
the computer. Information about all patches of the RFX-
2000 is sent to the computer via a MIDI link and can be
stored on the hard disk as a project file. Within a project, the
order of patches can be changed, and information stored as
project files can be loaded back into the RFX-2000. In
effect, this increases the memory capacity of the RFX-2000
to an unlimited size.
(2) Visual editor
Using sliders and other graphical elements appearing on the
computer screen, patches contained in project files can be
edited. Because the edited contents are sent immediately to
the RFX-2000 via the MIDI link, the aural effect of any
editing operation can be checked immediately. Edited
patches can be stored on the computer and can also be sent
to the RFX-2000 via the MIDI link.
(3) EXTRA bank
Using this software gives access to effects from the EXTRA
bank that cannot be selected in the same way as the other
effects at the unit. These effects comprise a custom reverb
with extensive control over many parameters, a 31-band
equalizer, a 20-tap delay effect, etc. The additional effects
further increase the application scope for the RFX-2000. By
storing a patch containing an effect from the EXTRA bank
in the memory of the RFX-2000, the effect can then be
called up like other patches, and some major parameters of
the effect can be edited with the controls of the RFX-2000.
• For information on software installation, please
refer to the separate sheet. For information on
how to use the software, please refer to the
documentation included on the CD-ROM.
• The latest version of the software can be
downloaded from the Zoom web site.
URL: http://www.zoom.co.jp
Supplied Software
Bekijk gratis de handleiding van Zoom RFX-2000, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Zoom |
| Model | RFX-2000 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4882 MB |
