Zodiac Ei3 handleiding
Handleiding
Je bekijkt pagina 11 van 20
Page 11
Page 10
Ei3 Saltwater Chlorinator | Installation Manual
6.2 Initial start-Up
The following setting must be configured at the
initial start up of the device. Settings can be
changed or updated at a later time using the
general menu, details can be found in Section 7.
From factory, the chlorination is set at 50 %. It can
be set between 0 and 100 % in 10 % increments
from the “main screen” by pressing
. The set
value is valid until the next modification.
6.2.1 System Power
1. Press
to enter Standby mode.
2. Press again to start chlorination and
ltration.
3. Press and hold
for 3 seconds to turn the
controllero.
6.2.2 Language
1. Press .
2. Use to select “Language”
then press
.
3. Use to browse language the options.
4. Press to make a selection.
<-LANGUAGE
MAIN MENU
<-ENGLISH
-FRANCAIS
-ESPANOL
-ITALIANO
-DEUTSCH
-NEDERLANDS
-PORTUGUES
-CESTINA
-MAGYAR
-SVENSKA
-SLOVENSKY
SELECT LANGUAGE
6.2.3 Set Clock
1. Press
.
2. Use to select “Programming”
then press
.
3. Use to select “Clock”
then press
.
4. Use to set hour then press .
5. Use to set minutes then press .
NOTE:
Press and hold or to increment time by 10.
6. Press to exit.
<-PROGRAMMING
-LOW MODE
-SLAVE MODE
MAIN MENU
23:04
CLOCK SET UP
6.2.4 Boost Mode
In some cases, the pool may require a higher than
normal chlorination level such as in cases of high
use, poor weather or at the start of the season. Boost
mode is used to increase the chlorine level quickly.
Boost mode lasts for 24 cumulative hours at 100%
production output. If the filter pump is connected
to the controller, the filter pump will operate in
Boost mode also. The controller’s operating
times including filtration schedules are temporarily
ignored for the duration of the Boost mode. This
is notable if you have a 12-hour ON followed by a
12-hour OFF cycle, as it will temporarily be a 24-
hour ON cycle during Boost Mode. Once Boost
mode completes, the controller and filter pump will
resume programmed operations.
1. Press
.
23:04 ON
BOOST MODE 23:59
2. If the controller is in Low/Cover mode you will
needtoconrmthatyouwantBoostmodeto
override Cover or Low mode settings.
6.2.5 Low Mode
Low mode is designed to reduce chlorine
production in situations where the pool is covered
or when pool use is limited. Chlorine production
needs will be lower when pool use is low and/or
when pool water is not exposed to UV rays etc.
Low mode output can be set in the main menu
settings for Low mode. Low can be set from
0%-30% in 10% increments. Programs are still
active while the controller is in Low/Cover mode.
1. To manually enter Low mode press
.
2. To exit Low mode press
again.
23:04 ON
LOW MODE 10%
6.2.6 Cover Mode
If the pool is equipped with a compatible electric roller
cover, this can be connected to the controller in order
to automatically reduce chlorination upon closing the
cover, this is known as Cover mode, see Table 3 and
Figure 7 for wiring details. Chlorination will resume
at the level determined by the programming upon
opening the compatible electric cover.
Cover mode output can be set in the main menu
settings for Low mode. Low can be set from
0%-30% in 10% increments. Programs are still
active while the controller is in Low/Cover mode.
Bekijk gratis de handleiding van Zodiac Ei3, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Zodiac |
| Model | Ei3 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2612 MB |
