Yato YT-83032 handleiding
Handleiding
Je bekijkt pagina 10 van 52
10
ORIGINAL INSTRUCTIONS
EN
indicated in the documentation of the battery. While replenishing the level of electrolyte, observe strictly the recommendations
indicated in the documentation of the battery.
The rectifi er has been designed uniquely for charging the so called „wet”, gel or AGM acid-lead batteries.
The rectifi er is equipped with exchangeable connections:
- alligator clamps – to charge most batteries,
- eye clamps – to fi x the terminals of the rectifi er to the battery terminals,
- vehicle electrical installation socket – to feed devices equipped with an adequate plug,
- vehicle electrical installation plug – to charge batteries through vehicle electrical installation socket or to maintain the power
supply in the vehicle electrical installation once the battery has been dismounted. Before operation in this mode commences, it is
necessary to get acquainted with the documentation of the vehicle.
Connect the selected terminals to the socket of the rectifi er. The plug of the terminals and the socket of the rectifi er have a protru-
sion permitting a correct connection.
Connect the terminals of the rectifi er to the terminals of the battery, make sure the terminal of the rectifi er marked with a „+” is
connected to the terminal of the battery marked with a „+”, and the terminal of the rectifi er marked with a „-” is connected to the
terminal of the battery marked with a „-”.
Connect the plug of the power cord to the power supply socket. For a moment all the diodes of the control panel will go on, and
then only the diode below the power supply symbol should remain lit.
Using the „MODE” switch, select the required mode of operation, which is confi rmed with a diode over the corresponding symbol.
Attention! Before the charging parameters are selected, get acquainted with the indications of the manufacturer of the battery.
Motorcycle symbol - to charge batteries whose capacity is lower than 40 Ah. Rated voltage 14.4 V; rated current 2.0 A.
Car symbol – to charge batteries whose capacity is lower than 160 Ah. Rated voltage 14.4 V; rated current 8.0 A.
Snowfl ake symbol – this mode is recommended for charging batteries in low temperatures. The mode of operation recommended
to charge in temperatures below +5°C and to charge many AGM batteries. Rated voltage 14.7 V; rated current 8.0 A. It is not
recommended to use this mode of operation to charge batteries in temperatures exceeding + 5°C.
Key symbol – desulfurization of batteries. When the rectifi er detects the rated voltage of the battery is lower than 10.5 V, it starts
desulfurization of the battery. The voltage on the terminals of the battery will be automatically increased to 17 V. Desulfurization
may last between 0.5 to 2 hours. If the process fails, it will be interrupted and the diode indicating failure will go on – the exclama-
tion mark.
Vehicle electrical installation symbol - the mode of operation with the vehicle electrical installation plug connected. Rated voltage
13.5 V; rated current 5.0 A. Maximum output power 72 W.
Explanation of the indicator lights
Power supply symbol – if the diode is lit, the rectifi er is connected to the power supply network.
Exclamation mark – if the diode is lit, the rectifi er is functioning incorrectly (short circuit, incorrect polarization or damaged bat-
tery)
Symbol of the battery (half full) – indicates the process of charging of the battery
Symbol of the battery (full) – indicates the battery is completely charged
Once charging has concluded, take the power cord out of the socket and then disconnect the terminals of the charging cables.
MAINTENANCE OF THE DEVICE
The device does not require any special maintenance. A dirty housing should be cleaned with a soft cloth or with a compressed
air jet, whose pressure must not exceed 0.3 MPa.
Check the conditions of the terminals of the conductors before and after each use. Remove any signs of corrosion, which might
disturb the fl ow of the electric current. Avoid contamination of the terminals with the electrolyte from the accumulator, since it would
accelerate the process of corrosion.
The device should be stored in a dry place, away from unauthorised persons, particularly children. Make sure the cables and
conductors are not damaged during storage.
Bekijk gratis de handleiding van Yato YT-83032, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Yato |
| Model | YT-83032 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4968 MB |
