Yaesu FT-847 handleiding
Handleiding
Je bekijkt pagina 12 van 108
10
FT-847 OPERATING MANUAL
ANTENNA CONSIDERATIONS
Installation
The antenna systems connected to your FT-847 trans-
ceiver are, of course, critically important in ensuring
successful communications. The FT-847 is designed
for use with any antenna system providing a 50Ω re-
sistive impedance at the desired operating frequency.
While minor excursions from the 50Ω specification
are of no consequence, the power amplifier’s protec-
tion circuitry will begin to reduce the power output of
there is more than a 50% divergence from the speci-
fied impedance (less than 33Ω or greater than 75Ω,
corresponding to a Standing Wave Ratio (SWR) of
1.5:1).
Four antenna jacks are provided on the rear panel of
the FT-847, using two different types of connectors.
Three of these jacks are “Type M” (SO-239) jacks;
these are the HF, 50 MHz, and 144 MHz jacks. The
other jack is a “Type N” jack, which is the 430 MHz
jack.
The center pins of these two jack types are of very
different diameters, and damage (not covered by your
transceiver’s Limited Warranty) will be caused if you
attempt to connect a Type M (PL-259) plug to the 430
MHz Type N jack. It is best to confirm visually that
you are connecting your coaxial cables to the correct
jacks.
Guidelines for successful base and mobile station in-
stallations are shown below.
Base Station Antenna
Installations
When installing a “balanced” antenna such as a Yagi
or dipole, remember that the FT-847 is designed for
use with an (unbalanced) coaxial feedline. Always
use a balun or other balancing device so as to ensure
proper antenna system performance.
Use high-quality 50Ω coaxial cable for the lead-in to
your FT-847 transceiver. All efforts at providing an
efficient antenna system will be wasted if poor qual-
ity, lossy coaxial cable is used. Losses in coaxial lines
increase as the frequency increases, so a coaxial line
with 0.5 dB of loss at 7 MHz may have 6 dB of loss at
432 MHz (thereby consuming 75% of your
transceiver’s power output!). As a general rule, smaller-
diameter coaxial cables tend to have higher losses than
larger-diameter cables, although the precise differences
depend on the cable construction, materials, and the
quality of the connectors used with the cable. See the
cable manufacturers’ specifications for details.
For reference, the chart below shows approximate loss
figures for typically-available coaxial cables frequently
used in HF installations.
CABLE TYPE
L
OSS
1.8 MHz 28 MHz 432 MHz
RG-58A 0.55 2.60 >10
RG-58 Foam 0.54 2.00 8.0
RG-8X 0.39 1.85 7.0
RG-8A, RG-213 0.27 1.25 5.9
RG-8 Foam
0.22 0.88 3.7
Belden 9913 0.18 0.69 2.9
7/8" "Hardline" <0.1 0.25 1.3
Loss in dB per 30m (100 feet)
for Selected 50
Ω
Coaxial Cables
(Assumes 50Ω Input/Output Terminations)
Loss figures are approximate;
consult cable manufacturers'
catalogs for complete specifica-
tions.
Bekijk gratis de handleiding van Yaesu FT-847, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Yaesu |
| Model | FT-847 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 17150 MB |
