Xblitz Mirror View handleiding

Handleiding

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758/ 58

Afdrukken

Je bekijkt pagina 9 van 58

16 17

2. Rear-view camera

3. Back-up camera connecon cable

4. Memory card reader

5. Instrucons

6. Charger

7. Fastening elascs

02. BEFORE USE

1. It is recommended to use original micro SD cards of class 10 or higher.

2. Before inserng the card into the recorder, it must be formaed in

the computer in the FAT32 or exFAT le system (depending on the

card) and then in the recorder.

3. The memory card must be installed when the device is switched

o otherwise the card and the device may be damaged. The same

applies when removing the card.

4. A fully charged baery allows recording without power for max. 5

minutes.

5. When the memory card lls up, the oldest unprotected recordings

will be overwrien if the RECORDING IN BAND funcon is acvated.

6. Use the funcons of the device according to their intended use, i.e.

do not use the MOVEMENT DETECTION and PARKING MODE while

driving. This may cause the device to switch on and o automacally,

e.g. when stopping at an intersecon.

7. The G-Sensor opon is recommended to be set to the lowest possible

value in order to avoid securing recordings that may be caused by

unevenness on the road.

8. Sound: the device has a condenser microphone that records all

ambient sounds. Sounds may overlap causing distoron.

9. The camera will start recording automacally when connected to

power.

03. CAMERA INSTALLATION

SEE FIG. A

1. Insert the memory card into the camera.

2. Aach the camera to the rear-view mirror.

3. Aach the camera using the rubber bands supplied with the camera

in the kit.

4. Route the power cable and the reversing camera cable.

5. Connect the power cable and the reversing camera cable.

6. Connect the power supply to the cigaree lighter socket.

The mounng locaon of the rear camera depends on your preference. The

camera complies with waterproong standards IP67 (completely dustproof

and protected against immersion in water - max. 30 minutes at a depth of

up to 1 metre).

Back-up camera installaon:

1. Connect the black cable supplied with the kit to the AVIN port on the

main unit, drag it to the mounng locaon and plug it in. Ensure that

the main unit can see the secondary camera (if not, check that the

cable is correctly inserted into both ports).

2. To use the rear view camera as a reversing camera before connecng

it to the DVR, it must be connected to the reverse light supply wires

(red = plus).

3. The installaon carried out outdoors should be well insulated and

should not be mechanically stressed.

04. PRODUCT DESCRIPTION

SEE FIG. B

1. Locaon of rubber bands

2. Lens

3. Loudspeaker

4. RESET buon

5. Micro SD card port

6. AV input (connecon point for rear camera)

7. Mini USB port (camera power supply)

8. MODE buon

9. UP buon

10. POWER buon

11. Down buon

12. OK buon

13. Microphone

05. GETTING STARTED

1. Mount and connect the camera to the power supply.

2. Insert micro SD memory card.

NOTE: Please only insert and remove the memory card when the device

is switched o.

3. Set in the menu:

a. Date and me.

b. Loop recording (adjust recording me). If you turn o loop

recording, the les will not be overwrien.

c. Set your preferred resoluon (it is recommended to use the

12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758/ 58

Bekijk gratis de handleiding van Xblitz Mirror View, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Andere merken in Fornuis