Wolf 801641 handleiding
Handleiding
Je bekijkt pagina 2 van 8
MODEL 801641
Page 2
20½"
11"
dia.
hole
20½"
10
3
/
8"
1¼"
dia. hole
10
3
/
8"
8½"
8½"
20¾"
20¾"
7¼"
7¼"
1¼"
dia. hole
9
1
/
8"
9
1
/
8"
REMOVE
SHINGLES
Roof Rafter
REMOVE
SHINGLES
11"
dia.
hole
Roof Rafter
Pilot
Pilot
Hole
Hole
Pilot
Hole
OUTSIDE - ROOF VIEW
OUTSIDE - ROOF VIEW
7"
2"
29½"
25"
2"
For flat roof installations:
q 4
Build a curb that will mount the blower at a minimum pitch
of 2/12. Discharge end of the blower should be pointed
away from prevailing winds.
ROOF MOUNT
INSTALLATION
For use with Wolf CTWH30/CTWH36 wall mount, IH4227 island chimney hoods, DD30R/DD36R downdraft ventilators, 10” tall
& 30-54” wide x 18” tall wall hoods, 36-54” x 18” tall island hoods & 12” tall liners.
PREPARE THE ROOF
INSTALL THE VENTILATOR
OUTSIDE - ROOF VIEW
OUTSIDE - ROOF VIEW
OUTSIDE - ROOF VIEW
OUTSIDE - ROOF VIEW
7 Cover
7 Cover
Screws
Screws
7 Cover
Screws
6
Mounting
Holes
6
Mounting
Holes
Shipping
Cardboard
Shipping
Cardboard
Remove
roofing
nails from
top 2/3 of
shingles.
Remove
roofing
nails from
top 2/3 of
shingles.
Flashing Sheet
Bird Screen
Bird Screen
Wiring
Cover
WIRE THE VENTILATOR
From inside the attic space:
q 1
Drill a PILOT HOLE up through the roof, 8½" from the
inside edge of a ROOF RAFTER.
From outside - on the roof:
q 2
Measure and mark the 20¾" x 20½" rectangle. Cut and
remove only the shingles inside this rectangle.
q 3
Measure and mark the 11" DIAMETER HOLE and the
1¼" DIAMETER HOLE. Cut these holes all the way through
the roof.
q 8
Remove SHIPPING CARDBOARD from blower wheel.
q 9
Remove roofing nails from top 2/3 of shingles around cut-
out area.
q 10
Slide the ventilator's FLASHING SHEET up and under
the loosened shingles until ventilator's discharge collar
fits into 11" diameter hole.
q 11
Use the 6 screws (provided) to attach the ventilator to the
roof. 6 MOUNTING HOLES are provided.
q 12
Seal the screw heads, loosened shingles, and edges of
the flashing sheet, with a good grade of roofing cement.
q 13
Check for free movement of the spring-loaded damper,
re-install BIRD SCREEN and ventilator cover. Turn on
power and check operation.
120 VAC
LINE IN
BLACK
TO
BLACK
WHITE
TO
WHITE
GREEN
TO
GREEN
q 5
Remove 7 COVER SCREWS and lift off ventilator cover.
Remove BIRD SCREEN and WIRING COVER.
q 6
Feed the electric power cable through the 1¼" DIAMETER
HOLE and connect cable to ventilator with a proper
connector for the type of cable being used.
q 7
Connect BLACK TO BLACK, WHITE TO WHITE, and the
GREEN TO GREEN or bare wire. Replace wiring cover.
Bekijk gratis de handleiding van Wolf 801641, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Wolf |
| Model | 801641 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1358 MB |
