Handleiding
Je bekijkt pagina 20 van 25
20
HVAD DU SKAL GØRE, HVIS DER OPSTÅR ET PROBLEM
Kogepladen eller kogezonen tænder ikke:
• Forbindelsen til netværket er forkert.
• Beskyttelsessikringen er frakoblet.
• Låsefunktionen er aktiveret.
• De følsomme taster er dækket af fedt eller vand.
• Der er placeret en genstand på en tast.
Betjeningspanelet viser [ ]:
• Der er intet kogegrej på kogezonen.
• Kogegrejet er ikke kompatibel med induktion.
• Diameteren af kogegrejets bund er for lille.
Betjeningspanelet viser [ ] :
• Det elektroniske system er defekt.
• Afbryd og tilslut kogepladen igen ved afbryderen.
En eller alle kogezoner slukker:
• Sikkerhedssystemet er aktiveret.
• Du har glemt at slukke for kogezonen i lang tid.
• En eller flere følsomme taster er dækket.
• Kogegrejets bund er tom og overophedet.
• Kogepladen har også en automatisk reduktion af varmetrinnet for at forhindre overophed-
ning
Ventilationen fortsætter, efter at kogepladen er slukket:
• Dette er ikke en fejl. Blæseren fortsætter med at køre for at beskytte de elektroniske kompo-
nenter.
• Blæserkølingen stopper automatisk.
Det automatiske tilberedningssystem starter ikke:
• Kogezonen er stadig varm [ H ].
• Det højeste varmetrin er indstillet [ 9 ].
Betjeningspanelet viser [ ] :
• Se kapitlet “Børnesikringsfunktion”
Betjeningspanelet viser [ ] eller [ ] eller [ ] :
• Se kapitlet “Keep warm”.
Betjeningspanelet viser [ ]:
• Se kapitlet “Pause”.
Betjeningspanelet viser [ ] eller [ ] :
• Betjeningstasterne er dækket af et objekt eller vand. Symbolet forsvinder, så snart tasten
frigøres eller rengøres.
Betjeningspanelet viser [ ] :
• Kogepladen er overophedet. Lad den køle af, og tænd den igen.
Betjeningspanelet viser [ ] :
• Ventilatorens luftindtag er blokeret. Fjern blokeringen.
Betjeningspanelet viser [ ] :
• Kogepladen er ikke tilsluttet til netværket. Kontroller ledningerne og tilslut kogepladen igen.
Betjeningspanelet viser [ ( ) ] :
• Sluk kogezonen, fjern alt kogegrej og lad kogeapparatet køle af. Genstart kogepladen.
Betjeningspanelet viser [ ( ) ] :
• Sluk kogezonen, fjern alt kogegrej og lad kogepladen køle af. Genstart kogepladen.
Hvis et af symbolerne ovenfor fortsat vises, skal du ringe til eftersalgsservicen.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
22
WHAT TO DO IN CASE OF A PROBLEM
The hob or the cooking zone doesn’t start-up :
• The connection to the network is wrong.
• The protection fuse has disconnected.
• The locking function is activated.
• The sensitive keys are covered with grease or water.
• An object is put on a key.
The control panel displays [ ]:
• There is no pan on the cooking zone.
• The pan is not compatible with induction.
• The bottom diameter of the pan is too small.
The control panel displays [ ] :
• The electronic system is defective.
• Disconnect and reconnect the hob at the circuit breaker.
One or all cooking zone cut-off :
• The safety system is activated.
• You forgot to turn off the cooking zone for a long time.
• One or more sensitive keys are covered.
• The pan is empty and its bottom overheated.
• The hob also has an automatic reduction of power level to prevent overheating
Continuous ventilation after turning off the hob :
• This is not a failure; the fan continues to run to protect the electronic components.
• The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
• The cooking zone is still hot [ H ].
• The highest power level is set [ 9 ].
The control panel displays [ ] :
• Refer to the chapter “Childlock fonction” page.
The control panel displays [ ] or [ ] or [ ] :
• Refer to the chapter “Keep warm”.
The control panel displays [ ]:
• Refer to the chapter “Pause”.
The control panel displays [ ] or [ ] :
• An object or liquid covers the control keys. The symbol disappears as soon as the key is released or
cleaned.
The control panel displays [ ] :
• The hob is overheated, let it cool and then turn it on again.
The control panel displays [ ] :
• The air inlet of the ventilator is obstructed, release it.
The control panel displays [ ] :
• The hob is not connected to the network. Check the wiring and reconnect the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
The control panel displays [ ( ) ] :
• Switch off cooking zone, remove all cookware and let the cooking appliance cool down. Restart the hob.
If one of the symbols above persists, call the After-Sales Service.
Bekijk gratis de handleiding van Witt WIF78EVW, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Witt |
| Model | WIF78EVW |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 2607 MB |
