Handleiding
Je bekijkt pagina 27 van 59
27
GEBRUIK EN PROGRAMMERING VAN DE DIGITALE KLOK OP HET AANRAAKSCHERM
MIN
INSTELLINGSKNOP
PLUS
Met de digitale klok kan de oven zo worden geprogrammeerd dat hij automatisch kan worden
in- en uitgeschakeld.
Dit bedieningspaneel fungeert als aanraakscherm; houd de vingertoppen een paar seconden lang
op de toets om hem te activeren.
EERSTE KEER INSCHAKELEN EN TIJD INSTELLEN
Bij de eerste keer inschakelen van het apparaat na een stroomonderbreking wordt 'AUTO' op het
display weergegeven. Druk op de knop . Het knipperen stopt. Gebruik de knoppen om de
tijd in te stellen (houd de knoppen ingedrukt om snel te scrollen).
Als u tijdens normaal bedrijf de tijd wilt instellen, dus als de klok al is ingeschakeld, moet u
tegelijkertijd beide toetsen minstens twee seconden ingedrukt houden en vervolgens de tijd
zoals hierboven beschreven instellen.
HANDMATIG GEBRUIK
Deze functie is voor gebruik van de oven zonder programmering.
U kunt altijd overstappen van een geprogrammeerde functie naar de handmatige functie door op
de knop te drukken en 'handmatig' te kiezen als er geen bereidingsprogramma's hoeven worden
gebruikt.
DE TIMER PROGRAMMEREN
Deze functie activeert een geluidsalarm na een vooraf ingestelde periode, zonder dat dit invloed
heeft op de werking van de oven.
De digitale klok kan ook als timer worden gebruikt:
• Druk ten minste 2 seconden lang op de knop om het programmeringsmenu te openen. Het
symbool wordt knipperend weergegeven.
• Gebruik de knoppen
Instructions for the user
28
USING AND PROGRAMMING THE DIGITAL CLOCK ON TOUCH SCREEN OVENS
The digital clock enables the oven to be set to automatically switch on and off.
DECREASE KEY
MODE KEY
INCREASE KEY
This programmer works like a touch screen; rest the tip of the finger on the key for a few seconds
to activate it.
INITIAL POWER-ON AND SETTING THE TIME
When first powering on the appliance or following a power failure, and the word AUTO flash
on the display. Touch the “Mode” key to stop the flashing and use the
/ keys to set the time
(hold down the / keys to scroll rapidly).
To adjust the time under normal operating conditions, i.e. when the clock is already on, touch both
keys / simultaneously for at least two seconds and then set the time as described previously.
MANUAL USE
This function is for using the oven without any programming.
It is always possible to switch from a programmed function to “Manuale” (Manual) function, by
touching the “Mode” key; choose “Manuale” if no cooking programmes are to be used.
PROGRAMMING THE TIMER
This function activates an audible alarm after a preset time, without interfering with the
operation of the oven.
The digital clock can also be used as a timer:
• touch the “Mode” key for at least 2 seconds to enter the programming menu; the flashing
symbol will appear;
• use the / keys to set the required time and the display will show the time remaining.
The timer starts automatically and the symbol will stop flashing. When the set time is reached,
an audible alarm sounds for 7 minutes and the symbol will flash;
• touch any key to stop the alarm or the “Mode” key to delete the programme.
om de gewenste tijd in te stellen; het display geeft de resterende tijd
weer. De timer start automatisch en het symbool stopt met knipperen. Als de ingestelde tijd is
verstreken, klinkt 7 minuten lang een alarm en knippert het symbool .
• Druk op een willekeurige knop om het alarm te stoppen of druk op om het programma te
wissen.
Gebruiksaanwijzing
Instructions for the user
28
USING AND PROGRAMMING THE DIGITAL CLOCK ON TOUCH SCREEN OVENS
The digital clock enables the oven to be set to automatically switch on and off.
DECREASE KEY
MODE KEY
INCREASE KEY
This programmer works like a touch screen; rest the tip of the finger on the key for a few seconds
to activate it.
INITIAL POWER-ON AND SETTING THE TIME
When first powering on the appliance or following a power failure,
and the word AUTO flash
on the display. Touch the “Mode” key to stop the flashing and use the
/ keys to set the time
(hold down the / keys to scroll rapidly).
To adjust the time under normal operating conditions, i.e. when the clock is already on, touch both
keys / simultaneously for at least two seconds and then set the time as described previously.
MANUAL USE
This function is for using the oven without any programming.
It is always possible to switch from a programmed function to “Manuale” (Manual) function, by
touching the “Mode” key; choose “Manuale” if no cooking programmes are to be used.
PROGRAMMING THE TIMER
This function activates an audible alarm after a preset time, without interfering with the
operation of the oven.
The digital clock can also be used as a timer:
• touch the “Mode” key for at least 2 seconds to enter the programming menu; the flashing
symbol will appear;
• use the / keys to set the required time and the display will show the time remaining.
The timer starts automatically and the symbol will stop flashing. When the set time is reached,
an audible alarm sounds for 7 minutes and the symbol will flash;
• touch any key to stop the alarm or the “Mode” key to delete the programme.
Instructions for the user
28
USING AND PROGRAMMING THE DIGITAL CLOCK ON TOUCH SCREEN OVENS
The digital clock enables the oven to be set to automatically switch on and off.
DECREASE KEY
MODE KEY
INCREASE KEY
This programmer works like a touch screen; rest the tip of the finger on the key for a few seconds
to activate it.
INITIAL POWER-ON AND SETTING THE TIME
When first powering on the appliance or following a power failure,
and the word AUTO flash
on the display. Touch the “Mode” key to stop the flashing and use the
/ keys to set the time
(hold down the / keys to scroll rapidly).
To adjust the time under normal operating conditions, i.e. when the clock is already on, touch both
keys / simultaneously for at least two seconds and then set the time as described previously.
MANUAL USE
This function is for using the oven without any programming.
It is always possible to switch from a programmed function to “Manuale” (Manual) function, by
touching the “Mode” key; choose “Manuale” if no cooking programmes are to be used.
PROGRAMMING THE TIMER
This function activates an audible alarm after a preset time, without interfering with the
operation of the oven.
The digital clock can also be used as a timer:
• touch the “Mode” key for at least 2 seconds to enter the programming menu; the flashing
symbol will appear;
• use the / keys to set the required time and the display will show the time remaining.
The timer starts automatically and the symbol will stop flashing. When the set time is reached,
an audible alarm sounds for 7 minutes and the symbol will flash;
• touch any key to stop the alarm or the “Mode” key to delete the programme.
Instructions for the user
28
USING AND PROGRAMMING THE DIGITAL CLOCK ON TOUCH SCREEN OVENS
The digital clock enables the oven to be set to automatically switch on and off.
DECREASE KEY
MODE KEY
INCREASE KEY
This programmer works like a touch screen; rest the tip of the finger on the key for a few seconds
to activate it.
INITIAL POWER-ON AND SETTING THE TIME
When first powering on the appliance or following a power failure, and the word AUTO flash
on the display. Touch the “Mode” key to stop the flashing and use the
/ keys to set the time
(hold down the / keys to scroll rapidly).
To adjust the time under normal operating conditions, i.e. when the clock is already on, touch both
keys / simultaneously for at least two seconds and then set the time as described previously.
MANUAL USE
This function is for using the oven without any programming.
It is always possible to switch from a programmed function to “Manuale” (Manual) function, by
touching the “Mode” key; choose “Manuale” if no cooking programmes are to be used.
PROGRAMMING THE TIMER
This function activates an audible alarm after a preset time, without interfering with the
operation of the oven.
The digital clock can also be used as a timer:
• touch the “Mode” key for at least 2 seconds to enter the programming menu; the flashing
symbol will appear;
• use the / keys to set the required time and the display will show the time remaining.
The timer starts automatically and the symbol will stop flashing. When the set time is reached,
an audible alarm sounds for 7 minutes and the symbol will flash;
• touch any key to stop the alarm or the “Mode” key to delete the programme.
Instructions for the user
28
USING AND PROGRAMMING THE DIGITAL CLOCK ON TOUCH SCREEN OVENS
The digital clock enables the oven to be set to automatically switch on and off.
DECREASE KEY
MODE KEY
INCREASE KEY
This programmer works like a touch screen; rest the tip of the finger on the key for a few seconds
to activate it.
INITIAL POWER-ON AND SETTING THE TIME
When first powering on the appliance or following a power failure,
and the word AUTO flash
on the display. Touch the “Mode” key to stop the flashing and use the
/ keys to set the time
(hold down the / keys to scroll rapidly).
To adjust the time under normal operating conditions, i.e. when the clock is already on, touch both
keys / simultaneously for at least two seconds and then set the time as described previously.
MANUAL USE
This function is for using the oven without any programming.
It is always possible to switch from a programmed function to “Manuale” (Manual) function, by
touching the “Mode” key; choose “Manuale” if no cooking programmes are to be used.
PROGRAMMING THE TIMER
This function activates an audible alarm after a preset time, without interfering with the
operation of the oven.
The digital clock can also be used as a timer:
• touch the “Mode” key for at least 2 seconds to enter the programming menu; the flashing
symbol will appear;
• use the / keys to set the required time and the display will show the time remaining.
The timer starts automatically and the symbol will stop flashing. When the set time is reached,
an audible alarm sounds for 7 minutes and the symbol will flash;
• touch any key to stop the alarm or the “Mode” key to delete the programme.
Bekijk gratis de handleiding van Witt Embrace 90 Gas, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Witt |
| Model | Embrace 90 Gas |
| Categorie | Fornuis |
| Taal | Nederlands |
| Grootte | 8345 MB |
