Witt Classic EHP60 handleiding

Handleiding

1234567891011121314151617181920212223242526272829303132333435363738394041424344/ 44

Afdrukken

Je bekijkt pagina 42 van 44

EN

42

then switch it on again.

Keep the control panel of the

heating areas clean and dry at all times.

In case of operating problems

or incidents not mentioned in this

manual, disconnect the appliance

and contact the WITT technical

service.

Recommendation for the

good use of vitroceramic

hobs

* Use pots or pans with thick,

completely at bottoms.

* Pans with a smaller diameter than

the shown heating area are not

recommended.

* Do not slide pots and pans over the

glass as they may scratch it.

* Although the glass can withstand

knocks from large pots and pans

without sharp edges, try not to

knock it.

* To prevent damage to the ceramic

glass induction surface, try not

to slide the pots and pans over

the glass, and keep the bottoms

of the vessels clean and in good

condition.

Try not to spill sugar or

products containing sugar on the

glass while the surface is hot as

these could damage it.

Cleaning and maintenance

To keep the appliance in good

condition, clean it using suitable

products and implements once it has

cooled down. This will make the job

easier and avoid the build-up of dirt

Never use harsh cleaning products or

tools that could scratch the surface, or

steam-operated equipment.

Light dirt not stuck to the surface can

be cleaned using a damp cloth and a

gentle detergent or warm soapy water.

However, for deeper stains or grease

use a special cleaner for ceramic hot

plates and follow the instructions on

the bottle. Dirt that is rmly stuck due

to being burned repeatedly can be

removed using a scraper with a blade.

Slight tinges of colour are caused by

pots and pans with dry grease residue

underneath or due to grease between

the glass and the pot during cooking.

These can be removed using a nickel

scourer with water or a special cleaner

for ceramic hot plates. Plastic objects,

sugar or food containing a lot of sugar

that have melted onto the surface

must be removed immediately using

a scraper.

Metallic sheens are caused by

dragging metal pots and pans over

the glass. They can be removed by

cleaning thoroughly using a special

cleaner for ceramic glass hot plates,

although you may need to repeat the

cleaning process several times.

A pot or pan may become

stuck to the glass due to a product

having melted between them. Do

not try to lift the pot while the hot

plate is cold! This could cause the

glass break.

Do not step on the glass or

lean on it as it could break and

cause injury. Do not use the glass

as a surface for putting objects.

WITT reserves the right to make

changes to its manuals that it deems

necessary or useful, without a󰀨ecting

the product’s essential features.

Environmental

considerations

The symbol on the product

or its packaging means that this

product cannot be treated like

ordinary household waste.This

product must be taken to a recycling

collection point for electrical and

electronic appliances. By ensuring

that this product is disposed of

correctly, you will avoid harming

the environment and public health,

which could happen if this product

is not handled properly. For more

detailed information about recycling

this product, please contact your

local authority, household waste

service or the store where you

purchased the product.

The packaging materials used are

environmentally-friendly and can

be recycled completely. Plastic

components are marked >PE<, LD<,

>EPS<, etc. Dispose packaging

materials, like household waste, in

your local container.

If something does not work

Before calling the technical service,

perform the verifications specified

below.

The appliance does not work:

Ensure that the power cable is plugged

in.

The pot sticks to the glass:

If there is molten material between

the pot and the glass, set the hot

plate to maximum power and try to

separate them.

Single Sensor Error :

If any of the sensors is active more

than 10 seconds, this error situation

occurs and error code”F1” is showed.

This error can be related with di󰀨erent

roots. One of them is that there may

be an object (fork, knife…) on the any

of the sensor.

Make sure that there is no any object

on the control unit, hob glass is wiped

with a dry cloth. If error situation

continue after this solution, please

take out plug or switch o󰀨 fuse switch

for 10 second.

Plural Sensor Error:

If more than 2 sensors are sensed at

same time, this error situation occurs

and error code”F2” is displayed.

Potential root reasons of the

problem :

• There may be an object(pot…) or

water accumulation(overow liquid

from pot…) that cover more than 2

sensors

• Touch control location may

exposure more heat or steam

(from oven bottom of the hob…)

Please be sure that there is no any

object on the sensors and switched o󰀨

all steam and heat sources. Then,hob

glass is wiped with a dry cloth. If error

1234567891011121314151617181920212223242526272829303132333435363738394041424344/ 44

Bekijk gratis de handleiding van Witt Classic EHP60, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.

Productinformatie

Andere merken in Niet gecategoriseerd