Handleiding
Je bekijkt pagina 6 van 40
6
Electrical Requirements
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person.
Do not use a cord that shows cracks or abrasion damage along its
length or at either the plug or connector end.
Recommended Grounding Method
A 115 V, 60 Hz AC-only 15 A or 20 A fused, grounded electrical
supply is required. It is recommended that a separate circuit
serving only your refrigerator be provided. Use an outlet that
cannot be turned off by a switch. Do not use an extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the refrigerator to Off. Depending on
your model, turn the refrigerator control to the word Off, or press
the refrigerator down arrow touch pad until a dash (–) appears in
refrigerator displays. Disconnect the refrigerator from the electrical
source. When you are finished, reconnect the refrigerator to the
electrical source and reset the temperature controls to the desired
setting. See “Using the Controls” in the Quick Start Guide.
Water Supply Requirements
Read all directions before you begin.
IMPORTANT:
� Connect to potable water supply only.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used
on disinfected waters that may contain filterable cysts.
� If you turn the refrigerator on before the water line is
connected, turn off the ice maker.
� All installations must meet local plumbing code requirements.
� Use copper or PEX tubing and check for leaks. Install copper
or PEX tubing only in areas where the household temperatures
will remain above freezing.
TOOLS NEEDED: Flat-blade screwdriver, 7/16" and 1/2"
open-end wrenches or 2 adjustable wrenches, 1/4" nut driver and
drill bit, cordless drill. Gather the required tools and parts before
starting installation. Read and follow the instructions provided with
any tools listed.
NOTE: Your refrigerator dealer has a kit available with a 1/4"
(6.35 mm) saddle-type shut-off valve, a union, and copper or PEX
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes. Do not use a
piercing-type or 3/16" (4.76 mm) saddle valve which reduces
water flow and clogs more easily.
Water Pressure
A cold water supply with water pressure of between 30 psi and
120 psi (207 kPa and 827 kPa) is required to operate the ice
maker. If you have questions about your water pressure, see
“Troubleshooting” online or call a licensed, qualified plumber.
Reverse Osmosis Water Supply
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 psi to 60 psi (276 kPa to
414 kPa). If the ice maker is still not operating properly:
� Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
� Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
If you have questions about your water pressure, see
“Troubleshooting” online or call a licensed, qualified plumber.
Connect the Water Supply
Read all directions before you begin.
IMPORTANT: If you turn on the refrigerator before the water line is
connected, turn off the ice maker to avoid excessive noise or
damage to the water valve.
Connect to Water Line
1. Unplug refrigerator or disconnect power.
2. Turn Off main water supply. Turn On nearest faucet long
enough to clear line of water.
3. Locate a 1/2" to 1
1
/
4
" (1.27 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
� Make sure it is a cold water pipe.
� Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
4. Determine the length of copper or PEX tubing you will need.
Measure from the connection on lower-left rear of refrigerator
to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use
1/4" (6.35 mm) O.D. (outside diameter) copper or PEX tubing.
Be sure both ends of copper or PEX tubing are cut square.
5. Using a cordless drill, drill a 1/4" hole in the cold water pipe
you have selected.
A. Cold water pipe
B. Pipe clamp
C. Copper or PEX
tubing
D. Compression
nut
E. Compression sleeve
F. Shut-off valve
G. Packing nut
Bekijk gratis de handleiding van Whirlpool WRTX5328PB, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Whirlpool |
| Model | WRTX5328PB |
| Categorie | Koelkast |
| Taal | Nederlands |
| Grootte | 7620 MB |
