Whirlpool WH3FB14BN7A0X handleiding
Handleiding
Je bekijkt pagina 8 van 32
8
TROUBLESHOOTING
PROBLEMS POSSIBLE CAUSES SOLUTIONS
Salt
indicator is lit
Salt reservoir is empty (after rell the salt indicator
may remain lit for several wash cycles).
Rell reservoir with salt (for more information - see page 2).
Adjust water hardness (see table, page 2).
Rinse aid
indicator is lit
Rinse aid dispenser is empty (after rell the rinse aid
indicator may remain lit for several wash cycles).
Rell dispenser with rinse aid (for more information - see page 2).
The dishwasher
won’t start or does
not respond to
commands.
The appliance has not been plugged in properly. Insert the plug into the socket.
Power outage.
For safety reasons, dishwasher will not restart automatically when power returns.
Press the START/Pause button to resume the cycle.
The dishwasher door is not closed.
NaturalDry pin is not pulled in.
Vigorously push the door until you hear the “click”.
Cycle is interupted by door opening for > 4 seconds.
Close the door and press START/Pause button.
It does not respond to commands. Display shows:
F9 or F12 and both On/O and START/Pause LEDs
are blinking rapidly.
Switch o the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and restart the program. If problem persists, unplug the
appliance for 1 minute, then plug it back in.
The dishwasher
won’t drain.
Display shows: F3
and both On/O
and START/Pause
LEDs are blinking
rapidly.
The wash cycle has not nished yet. Wait until the wash cycle nishes.
The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The lter is clogged up with food residues. Clean the lter (see CLEANING THE FILTER ASSEMBLY).
The dishwasher
makes
excessive noise.
The dishes are rattling against each other. Position the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has been produced.
The detergent has not been measured out correctly or it is not suitable for use in dish-
washers (see FILLING THE DETERGENT DISPENSER). Restart dishwasher by pressing the
DRAIN button (see OPTIONS AND FUNCTIONS) and run new program without detergent.
The dishes are not
clean.
The crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely, being hindered
by the dishes.
Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has been produced.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has not been
shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The lter is soiled or clogged. Clean the lter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher
does not ll the wa-
ter. Display shows:
and F6, both
On/O and START/
Pause LEDs are
blinking rapidly.
No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
The inlet hose is bent.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
After having carried out the verication and cleaning, turn o and turn on the dish-
washer and restart anew program.
Dishwasher nishes
the cycle prema-
turely. Display
shows: F15 and
both On/O and
START/Pause LEDs
are blinking rapidly.
Drain hose positioned too low or siphoning into
home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Air in water supply. Check water supply for leaks or other issues letting air inside.
Detergent leaks.
Depends on the liquid detergent used and can be
emphasized in case of Delay option is activated.
Small leaks will not cause machine malfunction and can be avoided by changing
liquid detergent type or using tablets.
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for aperiod of either up to 7 or up to 10 years, according to the specic Regulation requirements.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.whirlpool.eu/docs and parts-selfservice.europeanappliances.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our
After-sales Service, please state the codes provided on your product’s identication plate.
The model information can be retrieved using the QR-Code indicated on the energy label. The label also includes the
model identier that can be used to consult the https://eprel.ec.europa.eu database portal.
IEC 436
:
®/TM/ © 2024 Whirlpool, Produced under license
Bekijk gratis de handleiding van Whirlpool WH3FB14BN7A0X, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Whirlpool |
| Model | WH3FB14BN7A0X |
| Categorie | Vaatwasser |
| Taal | Nederlands |
| Grootte | 6296 MB |
