Handleiding
Je bekijkt pagina 11 van 70
.DESCALE
This special function, activated at regular intervals,
allows you to keep the steam system in the best
condition. Once the function is started, follow all the
steps indicated on the display. The average duration
of the full function is around 100 minutes. Descale
can be initiated anytime by the entering the then
selecting the "CLEANING FUNCTIONS" menu and the
Descale function. The display will show you when it
is time to run a Descale cycle. The number of hours
of steam cycles that must pass before the Decale
messages are shown depends on the water hardness
level set on the appliance and on the selected
steam functions, proportionally with the amount of
steam generated. The descaling procedure can also
be performed whenever the user desires a deeper
cleaning of the internal steam circuit. Before to run
the descaling phase, the appliance will check if some
residual water is contained into the boiler, and a Drain
cycle could be performed, if needed. In this case, you
will have to empty the drawer after the Drain cycle,
before continuing with the Descale Phase.
Please note: to ensure that the water is cold, it is not
possible to perform this activity before 40 minutes have
elapsed from the last cycle (or the last time the product
was powered). During this waiting time, the display will
show the following feedback “WATER IS HOT”.
» PHASE 1/2: DESCALING (70 MIN)
When display will show <ADD 0.25 L OF
SOLUTION>, please pour the descaling solution
in the drawer. For best results in descaling, we
recommend filling the tank with a solution
composed of 75 g of the specific WPRO
product and 250 ml of drinking water. WPRO
descaler is the suggested professional product
for the maintenance of the best performance
of your steam function in the oven. For orders
and information contact the after sales service
or www.whirlpool.eu.
Beko Europe will not be held responsible
for any damage caused by the use of other
cleaning products available on the market.
Once the descaling solution is poured inside
the drawer, press
to start the main
descaling process. The descaling phases do not
need you to stay in front of the appliance.
After each phase is completed, an acoustical
feedback will be played and the display will
show instructions to proceed with the next
phase.
Once the descaling phase has been completed,
the boiler will be drained: the descaling
solution used during this phase will be poured
into the extractable drawer. At the end of
the drain, drawers has to be extracted and
emptied.
» PHASE 2/2: RINSING (30 MIN.)
To remove descale residuals from the drawer
and the steam circuit, rinse cycle has to be
done. When display shows <ADD 0.25 L OF
WATER> fill the tank with 0,25 L of drinking
water, then press
to start the rinsing.
Do not turn off the oven until all the
steps required by the function have been
completed.
Please note: if needed from the system, it could be
requested to emty the drawer and to repeat this
operation.
When Descale procedure is completed
drawer has to be extracted and emptied, it
is suggested to dry the cavity from potential
water residuals. It will be then possible to use
all the steam functions.
Please note: during the Descale cycle, some noise
could potentially be heard since the oven pumps
are activated in order to guarantee the optimal
descale efficiency.
Once the maintenance cycle has started, do
not remove the drawer unless requested by
the appliance.
Please note: After the boiler gets filled by
the descaling solution and the display shows
“DESCALING PHASE 1/2”, the cycle should not be
interrupted, otherwise the entire descaling cycle
must be repeated before being able to run any
steam function.
. MINUTEMINDER
When the oven is switched off, the display can be
used as a timer. To activate this function, make sure
that the oven is switched off. Press and hold
icon
for 5 seconds: The
icon will flash on the display.
Press
or to set the length of time you require
and then press
to activate the timer.
MINUTE-MINDER
An audible signal will sound and the display will
indicate once the minuteminder has finished counting
down the selected time.
Please note: The minuteminder does not activate any of the
cooking cycles. Press or to change the time set on
the timer.
Once the minuteminder has been activated, you can
also select and activate a function.
Press
to switch on the oven and then select the
function you require. Once the function has started,
the timer will continue to count down independently
without interfering with the function itself.
Please note: During this phase, it isn’t possible to see the
minuteminder (only the icon will be displayed), that
will continue counting down in background. To retrieve the
minuteminder screen press to stop the function that is
currently active.
. KEYLOCK
To lock the keypad, press and hold for at least
1 + +2
= 75 g
250 ml
3
Bekijk gratis de handleiding van Whirlpool WCS7A9PHTSSGA, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Whirlpool |
| Model | WCS7A9PHTSSGA |
| Categorie | Oven |
| Taal | Nederlands |
| Grootte | 12101 MB |
