Whirlpool WAM 764WKBC PL handleiding
Handleiding
Je bekijkt pagina 86 van 88
When the appliance is turned off, pressing 1 and 2 auxiliary function buttons are pressed for a long
time, a 3-2-1 countdown, and the total washing cycles completed on the appliance is displayed.
After the total washing cycle is displayed, the failure codes, if any, are displayed. Check the
information on the screen through the table below.
On-screen Information Cause Solution
Err
Safety algorithm is run on the
appliance.
Wait for the writing to pass. After pressing the auxiliary
function buttons 1 and 2, check the on-screen information.
SC
Your complaint is not solved during
the check.
Call the authorised service agent.
E5 Pump filter may be clogged.
Clean the pump filter.
See “Draining remaining water and cleaning the pump
filter”
section.
Try in spin cycle. If the issue is not resolved, call the
service.
E8
The machine may not be taking in
water.
• Turn on the taps.
• Make sure there is no water outage.
• Check the water inlet hose connection, if there is any
folding
on the hose, straighten it.
• Clean the pump filter. See “Draining remaining water and
cleaning the pump filter” section.
• Close the front cover of the machine. Make sure that the
cover is locked.
Run the machine one more time. If the issue is not
resolved, call the service.
E29
The product has switched to self
protection mode due to a supply
problem (line voltage, water
pressure, etc.).
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme
will be cancelled. See“Cancelling the programme” section.
If the issue persists, call the service.
E17
Excess foam is present in the
machine after the completed cycle.
• Store detergent in a closed and dry location. Do not store
in excessively hot places.
• Use smaller amounts of detergent for porous laundry like
tulle.
• Use amount of detergent appropriate to the amount of
laundry and the level of stain.
• Use only sufficient amount of detergent.
• Make sure you place the detergent in the appropriate
compartment.
• Run the Drum Cleaning programme with the machine
empty. See "Drum Cleaning" programme
If your machine does not include Drum Cleaning
programme, you can use Cotton 90C.
• After running a short programme without detergent,
check the machine. If the issue persists, call the service.
E18
Spin cycle is not initiated due to an
imbalance of the machine.
Check the laundry inside the machine. The amount of
laundry may not be sufficient. Try by increasing the
amount of laundry. The laundry may be causing an
imbalance; sort out the laundry by hand and distribute
evenly inside the appliance.
Retry in spin cycle.
E12
There may be water inside the
machine.
Unplug the machine.
There may be water under the machine. Clean the water
under the machine.
Plug the machine again.
Try running a short cycle.
If the issue persists or you see water leaking from one of
the hoses, close the valves and call the service.
E27
Check the water drain of the
machine.
See “Connecting the drain hose to the drain”section.
E84
BLE connection cannot be
established.
Check it, try connecting it. See “HomeWhiz Feature and
Remote Control Function” section. If the issue persists,
call the service.
How to access the cycle counter
Bekijk gratis de handleiding van Whirlpool WAM 764WKBC PL, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Whirlpool |
| Model | WAM 764WKBC PL |
| Categorie | Wasmachine |
| Taal | Nederlands |
| Grootte | 8551 MB |
