Whirlpool TDLRB 6261BS handleiding

Wasmachine

Whirlpool

32 pagina's

PDF beschikbaar

Handleiding

TROUBLESHOOTING

The washing machine may sometimes not work properly for certain reasons. Before calling the After-sales service, it is recommended to check to see if the

problem can be easily resolved using the following list.

Anomalies: Possible causes / Solution:

The washing machine does not turn on

and/ or programme does not start

• The plug is not inserted into the electrical outlet, or not enough to make contact.

• There has been a power failure.

• Lid is not properly closed.

• The “Child lock“ function has been activated (if available).

• The washing machine switched o automatically to save energy, before programme start or

after programme end. To switch on the washing machine, turn the programme selector rst to

“O/O” and then to the desired programme again.

The wash cycle does not start.

• The “Start/Pause“ button has not been pressed.

• The water tap is not open.

• A “Start delay“ has been set.

Appliance stops during the

programme, and the

“Start/Pause“ light blinks

• “Rinse hold“ option is activated (if available).

• Programme has been changed - re-select desired programme and press “Start/Pause“ .

Appliance vibrates

• The washing machine is not level.

• The transport bracket has not been removed; before using the washing machine, the transport

bracket must be removed.

Final spin results are poor. The laundry

is still very wet. “Spin/Drain“ indicator

blinks, or the spin speed on the display

blinks, or the spin speed indicator

blinks after the end of the programme

- depending on the model

• Unbalance of the laundry load during spinning prevented the spin phase to avoid damages on

the washing machine. This is why the laundry is still very wet. Reason for unbalance can be:

small laundry loads (consisting of only few quite big or absorbent items, e.g. towels), or big/

heavy laundry items.

• If possible avoid small laundry loads.

• “Spin“ button has been set to a low spin speed.

The machine is indicating an error code

(e.g. F-02, F-..) and/or “Service“

indicator lights up

• Shut o the machine, disconnect the plug from the outlet, and wait about 1 minute before

turning it back on.

• If the problem persists, call the After-sales service.

“Clean pump“ indicator lights up

• Waste water is not pumped out.

• Clean the water lter

“Water tap closed“ indicator lights

• Appliance has no or insucient water supply.

“Detergent over dosage“ indicator

lights up (if available)

• The symbol will light up at the end of the programme if you used too much detergent.

• Too much foam is formed.

• The detergent is not compatible with the washing machine (it must bear the wording “for

washing machines“, “for hand washing and washing machines“, or something similar).

You can download the Safety Instructions, Product Fiche and Energy data by:

• By visiting our website docs .whirlpool. eu and parts - selfservice .whirlpool. com

• Using QR Code

• Alternatively, contact our After-Sales Service (See phone number in the warranty booklet). When contacting our After-sales Service,

please state the codes provided on your product’s identication plate.

For User Repair & Maintenance Information visit www.whirlpool.com

You can nd more information about your model online at https://eprel.ec.europa.eu/ which is the ocial EU EPREL product database.

After selecting the Product Category, enter the Model Identier of the product. The Model Identier is made up of letters and numbers

and can be found on the identication plate, as Mod. (see image on the right).

xxxxxxxxxx

Bekijk gratis de handleiding van Whirlpool TDLRB 6261BS, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.