Whirlpool CAE2779JWH handleiding
Handleiding
Je bekijkt pagina 9 van 38
9
Troubleshooting
If you experience Possible Causes Solution
Washer not performing
as expected (cont.)
Washer won’t run
or ll; washer stops
working (cont.)
Normal washer operation. Lid must be closed for washer to run.
Washer will pause during certain phases of cycle. Do not
interrupt cycle.
Washer may be tightly packed. Press START (PAUSE/UNLOCK) for 3 seconds and wait for lid to
unlock. Remove several items, rearrange load evenly in basket,
and add detergent. Close lid and press START.
Do not add more than 1or 2 additional items after cycle has
started to avoid tightly packing or unbalancing.
Machine displays error Error code. Try unplugging washer for 10 seconds and plug it back in
to reset the control.
Refer to Tech Sheet.
Washer not
draining/
spinning, loads are still
wet, or spin light remains
on (indicating that the
washer was unable to
pump out water within
10 minutes)
Small items may have been caught
in pump or between basket and tub,
which can slow draining.
Empty pockets and use garment bags for small items.
Use a cycle with a low spin speed. Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/spin speed
for your garment. To remove extra water in the load on a nonpay
model, select Final Spin. Load may need to be rearranged to
allow even distribution of the load
in the basket.
The washer may be tightly packed
or unbalanced.
Tightly packed or unbalanced loads may not allow the washer
to spin correctly, leaving the load wetter than normal. Evenly
arrange the wet load for balanced spinning on a nonpay model.
Select the Final Spin cycle to remove excess water. See “Using
Your Washer” for loading recommendations.
Check plumbing for correct drain
hose installation. Drain hose
extends into standpipe farther
than 4.5" (114 mm).
Check drain hose for proper installation. Use drain hose form
and securely attach to drainpipe or tub. Do not tape over drain
opening. Lower drain hose if the end is higher than 96" (2.4 m)
above the oor. Remove any clogs from drain hose.
Too much detergent causing
suds to slow or stop draining
and spinning.
Always measure and follow detergent directions for your load.
To remove extra suds on a nonpay model, select Rinse & Spin.
Do not add detergent.
Dry spots on load
after cycle
High-speed spins extract more
moisture than traditional top-load
washers.
The high spin speeds combined with airow during the nal spin
can cause items near the top of the load to develop dry spots
during the nal spin. This is normal.
Incorrect or wrong
wash or rinse
temperatures
Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and
have both hot and cold water owing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
Energy-saving controlled-wash
temperatures.
This washer uses cooler wash and rinse water temperatures than
your previous washer. This includes cooler hot and warm washes.
Load not rinsed Check for proper water supply. Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water owing to the inlet
valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Using too much detergent. The suds from too much detergent can keep washer from
operating correctly. Always measure detergent and follow
detergent directions based on load size and soil level.
Before calling for service on your washer, please try the solutions suggested in this section.
Bekijk gratis de handleiding van Whirlpool CAE2779JWH, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Whirlpool |
| Model | CAE2779JWH |
| Categorie | Wasmachine |
| Taal | Nederlands |
| Grootte | 5179 MB |
