Wesco 272460 handleiding
Handleiding
Je bekijkt pagina 3 van 26
Page3of26
©Copyright 2018 WESCO Industrial Products, LLC. Specifications subject to change. Not responsible for errors or omissions.
Electric Non-Telescoping High Lift Truck
(Part # 272460 & 272461)
Instruction Manual
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR HIGH LIFT TRUCK,
READ THESE INSTRUCTIONS ENTIRELY BEFORE USING.
3. INITIAL ASSEMBLY
1) Insert the handle arm (Item 1, Fig. 2) into the pump
piston, then use a hammer to insert the axle with
hole into the hydraulic pump and handle arm from
right to the left (Fig. 3).
2) Set the control lever of the handle to the ‘LOWER’
position, then pass the adjusting nut, adjusting bolt
through the hole of the axle with your hand (Fig. 1).
3) Press the handle arm down; take away the pin
(Item 2, Fig. 2).
4) Set the control lever of the handle to ‘LIFT’
position, then raise the lever plate with the pin
(Item 2, Fig. 2) and insert the adjusting bolt into the
front slot of lever plate. Note: Keep the adjusting
nut under the lever plate.
5) Use a hammer to insert the 2nd dowel pin (Item 5,
Fig. 2) into the 2
nd hole of the axle. The draw-bar is
now assembled to the pump.
6) Connect the control cable. Fix the cable at the
pump side in a way that the cable holder can be
turned. Fix the cable before the plug with the pre
assembled cable strip.
4. HYDRAULIC VALVE ADJUSTMENT
On the handle of your pallet truck, you will find the control
lever, which can be regulated in three positions:
Lower : handle up, the lever moves back to the neutral
Neutral : handle in center position
Lift : handle down
If necessary, you can adjust the lever according to
following steps (Fig. 4):
• If the forks elevate while pumping in the Neutral
position, turn the adjusting nut on the adjusting bolt
clockwise until pumping does not raise the forks and the
Neutral position works properly.
• If the forks descend while pumping in the Neutral
position, turn the adjusting nut counter-clockwise until the
forks do not lower.
• If the forks do not descend when the control handle is in
the Lower position, turn the adjusting nut clockwise until
raising the control handle lowers the forks. Then check
the Neutral position according to fig. 4 and be sure that
the adjusting nut is in the proper position.
• If the forks do not elevate while pumping in the Lift
position, turn the adjusting nut counter- clockwise until the
forks elevate while pumping in the Raise position. Then
check the Lower and Raise position.
Figure 1 Side View with Labels
Figure 2 Handle Assembly
(1-Handle Arm/2-Pin/3-Nut/4-Axle with Hole/
5-Dowel Pin/6-Chassis with Pump Unit)
Figure 3 Axle Assembly
Figure 4 Lever Positions
Spring
Spring Cap
Pum
p
Piston
Roller PinRoller Pin
Pressure Roller
Chain
Draw-Bar
Axle With Hole
Adjusting Bolt
Adjusting Nut
Lever Plate
1
4
5
5 6
2
3
Lower
Neutral
Lift
Bekijk gratis de handleiding van Wesco 272460, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Wesco |
| Model | 272460 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6487 MB |
