Voltcraft TOPS-3363N handleiding
Handleiding
Je bekijkt pagina 5 van 16
5
Operating instructions
100 W Laboratory Power Supply
Item no. 3089717 TOPS-3205N
Item no. 3089718 TOPS-3363N
1 Operating instructions for download
Use the link www.conrad.com/downloads (alternatively scan the QR code) to download the
complete operating instructions (or new/current versions if available). Follow the instructions
on the web page.
2 Intended use
The laboratory power supply unit serves as a potential-free DC voltage source to operate low-
voltage loads. The connection is made at the front side via 4 mm safety sockets. In addition,
two independent power USB outputs are available.
Always observe the limitations of the adjustable outputs and the USB ports as stated in the
“Technical data”.
Adequately dimensioned connecting cables must always be used. A wire
cross-section that is too small can cause overheating and re.
Voltage and current adjustments are continuous via digital control button. By pressing on the
control button you can change from coarse to ne adjustment. This makes a quick and precise
adjustment of values possible. Values are displayed on a high-contrast LED display. The cur-
rent limit for the constant current mode can be preset without shorting.
The power supply can be controlled remotely from a Windows
®
computer via USB-A.
The device is overload and short-circuit-proof and contains a safety temperature cut-off. The
DC output is also overvoltage protected (OVP).
The design of the product complies with the safety class 1. Only supply the product with a volt-
age from an earthed standard mains socket connected to the public supply grid. The mains
socket must be near the device and easily accessible, or an emergency stop device must be
present.
Do not interconnect the outputs of multiple power packs. This can result in hazardous contact
voltages or in damage to the unit.
Operation in potentially explosive atmospheres (Ex) or wet areas or under adverse environ-
mental conditions is forbidden. Adverse environmental conditions are:
Damp or excess air humidity
Dust and ammable gases, vapours or solvents
Thunderstorms or similar conditions such as strong electrostatic elds, etc.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, res, electric shocks or other hazards.
The product complies with the statutory national and European requirements. For safety and
approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product
available to third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights
reserved.
USB4
®
, USB Type-C
®
and USB-C
®
are registered trademarks of USB Implementers Forum.
3 Package Contents
Power supply unit
1 pair of test leads with alligator clips
USB-A to USB-B cable
Power cable
Operating Instructions
4 Explanation of symbols
Read the operating instructions carefully.
An exclamation mark in a triangle refers to important information in these operating
instructions that must be adhered to.
The product is CE compliant and meets the requirements of the current European
and national guidelines.
Connection terminal for the internal protective earth; this screw/contact must not
be removed.
Ground potential, reference mass.
Only to be used in dry indoor areas.
5 Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting per-
sonal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
5.1 General information
The device is not a toy. Keep it out of the reach of children and pets.
Do not leave packaging material lying around carelessly. This may become dangerous
playing material for children.
If you have questions which remain unanswered by these operating instructions, contact
our technical support service or other technical personnel.
Maintenance, modications and repairs must only be completed by a technician or an au-
thorised repair centre.
5.2 Handling
Please handle the product carefully. Jolts, impacts or a fall even from a low height can
damage the product.
5.3 Operating environment
On industrial sites, the accident prevention regulations of the association of the industrial
workers‘ society for electrical equipment and utilities must be followed.
Power supply units used in schools, training facilities, do-it-yourself and hobby workshops
should not be handled unless supervised by trained, responsible personnel.
Do not place the product under any mechanical stress.
Protect the appliance from extreme temperatures, strong jolts, ammable gases, steam
and solvents.
Protect the product from high humidity and moisture.
Protect the product from direct sunlight.
Do not switch the product on after it has been taken from a cold to a warm environment.
The condensation that forms might destroy the product. Allow the product to reach room
temperature before you use it.
The base of the unit could chemically react considering the large variety of protection prod-
ucts for furniture. Place the device on a resistant, smooth and at surface.
5.4 Operation
The power supply unit is not designed for attaching to humans or animals.
Consult an expert when in doubt about the operation, safety or connection of the appliance.
If it is no longer possible to operate the product safely, take it out of operation and protect
it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation
can no longer be guaranteed if the product:
– the unit exhibits visible damage,
– does not function any longer and
– the unit was stored under unfavourable conditions for a long period of time or
– it has been subjected to considerable stress in transit.
The device must not be opened. Live parts may be exposed, if you open covers or remove
parts – unless you can do this by hand. Capacitors inside the device may still be charged,
even if the device has been disconnected from all voltage sources.
Observe the safety and operating instructions of any other devices you intend to connect
to the device, in addition to those contained in the individual chapters of these operating
instructions.
Never touch the device with wet or moist hands. There is danger of a life-threatening elec-
tric shock.
Do not leave mains power supplies and connected consumer devices in operation unat-
tended.
Only use fuses of the rated type and current. It is absolutely prohibited to use repaired
fuses.
Do not use non-insulated metallic leads.
Do not place any vessels with liquids on the device.
The device will become warm during operation. Ensure sufcient ventilation of the device.
Do not cover or seal the ventilation openings of the device. Make sure there is enough free
space on the sides.
Bekijk gratis de handleiding van Voltcraft TOPS-3363N, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Voltcraft |
| Model | TOPS-3363N |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2954 MB |
