Vestil WP-3636-CA-DD handleiding
Handleiding
Je bekijkt pagina 5 van 17
Table of Contents Rev. 4/12/2024 WP, MANUAL
Table of Contents Copyright 2023 Vestil Manufacturing Co. Page 5 of 17
SAFETY INSTRUCTIONS
We strive to identify all hazards associated with the use of our products. However, material handling is
dangerous and no manual can address every risk. The most effective way to avoid injury is for the end-user to
exercise sound judgment whenever using this product.
DANGER
Electrocution might result if an occupied work platform contacts electrified wires.
DO NOT contact electrified wires with any part of the platform, tools, or your body/clothing.
DO NOT use the platform in an area where contact with electrified wires might occur.
DO NOT use the work platform in close proximity to electrified wires or other sources of electricity.
WARNING
Risks of serious personal injuries or death.
Always conform to OSHA “Powered industrial trucks” and fall protection systems rules. See 29 CFR 1910.178.
Acquire a copy of the latest revision of American National Standard ANSI/ITSDF B56.1. The Standard is freely
downloadable from the ITSF website (http://www.itsdf.org/cue/b56-standards.html). Apply all recommended and
mandatory provisions regarding the use, inspection, care, and maintenance of platforms used to elevate personnel.
Contact the manufacturer of your lift truck to verify that the truck is capable of safely handling the fully loaded
platform. See NOTES on p. 2. The overall width of your platform must be equal to or less than the width of your
fork truck plus 10 inches (250mm).
DO NOT exceed the maximum occupancy ratings for each model: WP-series = 2; SP-175 = 1; WP-3737-FD = 2.
If your model allows for occupancy by 2 persons, each person must wear a safety harness and lanyard. Connect
the lanyard to a distinct anchor point. Anchor points are identified on p. 10. Each person must connect to a different
anchor point. DO NOT connect both harnesses to the same anchor point.
ONLY use the work platform to lift people and their tools. DO NOT exceed the capacity of the platform.
DO NOT use the work platform unless it is in SATISFACTORY CONDITION. Inspect the platform before each use
by applying the INSPECTION instructions on p. 6. DO NOT use the platform unless it is in SATISFACTORY
CONDITION passes every part of the inspection.
Platform occupants and fork truck operators must wear hard hats whenever this platform is used.
DO NOT use the platform if the safety chain/strap is damaged or missing.
DO NOT elevate the platform until it is securely connected to the carriage of the fork truck with the safety strap.
The safety chain/strap is the primary safety mechanism. It must be used every time the work platform is used! To
use the safety chain/strap properly, attach the device to the fork truck carriage as instructed in STEP 2 on p. 10.
Each work platform also includes a secondary safety feature called a tine lock that secures the platform to a tine
of your fork truck. However, the lock might not fit over the heel of the tine of your fork truck. If this is the case, do not
modify the tine lock. Although the platform can be used without applying the tine lock, it is strongly recommended
that the platform only be mounted on forks that allow use of the tine lock.
DO NOT attempt to support a load that weighs more than the platform’s capacity. The net weight, i.e. the sum of
the weight of all occupants and everything else supported by the platform, cannot exceed the capacity of the
platform.
DO NOT stand beneath or travel under the platform while it is elevated.
DO NOT use the gate(s), chains, mast guard, guardrails, etc. as a step.
Platform occupants must ALWAYS use personal fall protection equipment securely attached to the platform at an
anchorage point. See USING THE PLATFORM diagrams on p. 10-11. Only disconnect from an anchorage point
when the platform rests securely on the ground.
DO NOT use UNLESS each label is in place, undamaged and readable. See applicable LABELING DIAGRAM on
p. 12, 15, or 16.
Occupant safety depends on maintaining a work platform in level, horizontal position. Only use work platforms on
improved surfaces (asphalt or concrete) that are even and level.
DO NOT mount a work platform on a telehandler, aka boom lift, or rough terrain forklift, even if the handler will be
used on level concrete or asphalt.
ONLY use this work platform on a safe, well-maintained lift truck in proper working order.
The forklift operator must remain in the forklift whenever the work platform is occupied. DO NOT leave the
operator station of the forklift if the work platform is occupied.
Maintain uninterrupted communications between the lift truck operator and platform occupant(s) at all times.
The work platform must be equipped with an emergency stop switch whenever the platform is used in noisy areas
where communication between the forklift operator and platform occupant(s) is impaired. See EMERGENCY STOP
SWITCH INSTALLATION on p. 14.
Bekijk gratis de handleiding van Vestil WP-3636-CA-DD, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | WP-3636-CA-DD |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8273 MB |
