Vestil S-2CB-118 handleiding
Handleiding
Je bekijkt pagina 7 van 16
S-2CB, Manual.doc
Copyright 2015 Vestil Manufacturing Corp.
Page 7 of 16
Step 5: Drive the stacker to the desired location.
To steer the unit, turn the yoke to the right
or left of
the center line. Moving the yoke to the right will
cause the S-2CB to turn to the right, and moving
the yoke to the left of the center line will cause the
unit to turn left. The degree of deflection from the
centerline determines how sharply the S-2CB
turns. The illustration at right demonstrates how
the position of the yoke determines the direction
the machine follows.
Lifting and Transporting Loads
:
DO NOT operate the S-2Cb until you read AND understand every instruction. If you do not understand
an instruction, contact Vestil for clarification. To reduce the possibility of sustaining or causing serious personal
injuries, ALWAYS:
1. Make sure that all other persons clear the area while you use the S-2CB.
2. Apply the fork truck operation and lifting practices learned during your operator training, and applied by your
employer. Follow the instructions below ONLY to the extent that they do not disagree with the operating practices
required by your employer.
Make sure that the net weight to be lifted (load + skid) does not exceed the rated load (capacity) of your truck;
Center and evenly distribute the load on the forks. The load must not project more than 2” beyond the tips of the forks.
3. Review the safety guidelines on p. 3 before each use:
Apply proper loading techniques ;
Ask a coworker to help you load and unload the lifter.
4. “Operator” means a person, who is trained and authorized to use a manually propelled high lift device. ONLY
persons who have successfully completed a training program, like the courses outlined on p. 4-5 of
B56.10-2006, should operate the S-2CB. Safe operation requires operators to:
Develop safe working habits and a process for identifying hazards that exist or might be encountered during
operation;
Conduct thorough inspections of the usage area to identify unusual/hazardous conditions. Walk the path you will
use to transport loads with the lifter beforehand. Do not use the S-2CB lift if the floor (or other supporting
surface) is uneven or damaged or cannot support the combined weight of the operator, the lifter and the load.
Make sure that the lifter has been inspected as recommended in the “Inspections & Maintenance” section of this
manual (p. 19). Use the lifter ONLY IF it is deemed safe to use by designated inspection personnel.
To engage a pallet/skid, drive the unit to a position in front of the intended load. Before engaging the load, confirm
that the forks will fit within the fork pockets. Fully lower the forks to allow them to slide into the fork pockets of the
skid. Confirm that the net weight of the load plus the skid do not exceed the capacity of the S-2CB.
Continue forward until either the skid rests against the back
(vertical/upri
ght portion), or the forks are as far
underneath the skid as they can be. When the skid contacts the back of the forks, put the yoke in a neutral position to
stop forward motion. Wait until the stacker stops completely, and then lift the skid off of the ground/supporting
surface by pressing one of the two fork raising buttons.
Proper Transport Configuration: To avoid unintend
ed contact between the skid/pallet and surface features, transport
the load to the desired location with the forks elevated.
To release the load, stop in the desired location; fully lower the forks; and then slowly drive the S-2CB forward until
the forks are no longer beneath the skid/pallet.
Batteries and Charger
:
The charger allows electrical current to flow from
a wall socket through the batteries. While operating the
charger, contact with water (rain, sno
w, etc.) could result in
electric shock or electrocution. Do NOT recharge the batteries
if the S-2CB is outdoors. Only recharge the batteries indoors.
Turn off your S-2CB:
Push E-stop to turn off the S-2CB
Plug the charger’s AC cord into an 115VAC power source:
The AC cord is tucked inside the battery box on the left side
Press E-Stop
Bekijk gratis de handleiding van Vestil S-2CB-118, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | S-2CB-118 |
| Categorie | Vorkheftruck |
| Taal | Nederlands |
| Grootte | 2183 MB |
