Vestil PG-S-045 handleiding
Handleiding
Je bekijkt pagina 5 van 15
SAFETY GUIDELINES
Read the entire manual before attaching the pipe grab to a lifting device or using it for the first
time. Refer to the manual for safe use and maintenance procedures (p. 11-14). If questions
remain after you finish reading the manual, contact Vestil for answers. DO NOT attempt to resolve
any problems with the pipe grab unless you are certain that it will be safe to use afterwards.
NEVER modify the product in any way without the express written approval of Vestil.
• Electrocution Risk: DO NOT contact live electrical wires with the pipe grab or the load!
• Review the safety messages included in the manual(s) for the crane, trolley, hoist, and any other
device used in conjunction with the pipe grab.
• To open the grab, lift one or both of the pipe guide weldments. DO NOT open the grab while using it
to lift and/or move material.
• ALWAYS inspect the pipe grab before each use according to the inspection procedures described in
ASME B30.20. B30.20 also recommends “frequent” and “periodic” inspections.
• Properly maintain the pipe grab according to the maintenance procedures on p. 14. These
procedures were developed to supplement suggested maintenance practices of B30.20.
• ONLY attach the pipe grab to a safety hook (e.g. a hoist that has a safety hook connected to the end
of the chain or rope) or to a connection that includes safety features to prevent accidental/unintended
detachment from the hoist. DO NOT use the pipe grab on a hook that might release the grab. DO
NOT connect the grab to a safety hook that does not function properly or that is damaged.
• DO NOT grab a load that has any debris or surface contamination on it that might affect the quality of
the connection between the grab and the load. Remove all debris, such as oil, grease, dirt, or water.
• Clear all debris, including fluids, from the path of travel (if the job requires moving the load to a new
location) BEFORE picking up material. If moisture is present in the path of travel, absorb it before
using the grab to reposition the load. Make sure that no person is in the travel path.
• DO NOT remove or obscure any label. Verify the placement and legibility all labels as shown in FIG.
6 on p. 15. If any label becomes damaged or unreadable, contact Vestil for a replacement. DO NOT
use the grab UNLESS all labels are attached and readable.
• DO NOT attempt an unbalanced lift. Always use enough grabs to balance the load before lifting
and/or moving the load.
• DO NOT sit on or apply any weight/pressure to a load grasped by the pipe grab.
• DO NOT attempt to lift material that exceeds the load rating. ALWAYS make sure that the material
weighs no more than the rated load of the pipe grab.
• DO NOT lift a load higher than necessary. (See “Use Instructions” on p. 11-13).
• Stay clear of the suspended load. DO NOT raise the load over your feet or any other part of your
body. DO NOT use the pipe grab to lift material over people!
• DO NOT lift any apparatus that is used to support people, such as a work platform.
• Always orient yourself so that the load is visible to you. You are less likely to be injured by the load if
it remains within sight at all times. Standing to one side of the load next to the pipe grab will allow
you to stabilize the load as you move it to the desired location.
• DO NOT leave a suspended load unattended. An unattended, suspended load creates a risk of injury
to yourself and others. Always move a load to its desired location, set the material down and properly
immobilize it, and then disengage the grab from the load. Disconnect the grab from the hoist
BEFORE you leave the work area.
- 5 -
Bekijk gratis de handleiding van Vestil PG-S-045, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | PG-S-045 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6783 MB |
