Vestil OLA-2 handleiding
Handleiding
Je bekijkt pagina 6 van 8
Table of Contents Rev. 8/14/2025 OLA-2 MANUAL
Table of Contents Copyright 2020 Vestil Manufacturing Co. Page 6 of 8
b. OLA-2-36-DLX & OLA-2-42-DLX: slide
the bale along the lifting arm and seat
the bale pin into one of the pin slots in
the underside of the lifting arm.
i. Lifter tilts forward (fork tips down):
Shift bale mechanism towards the
free end of the lifting arm.
ii. Lifter tilts backwards (fork tips up):
Shift bale towards the back of the
lifting arm.
4. Minimize swinging! Make sure that the
hoist is centered above the bale, i.e. hoist
chain/rope is vertical. If the hoist
chain/rope is not vertical, the lifter will
swing as it is elevated.
5. Slowly raise the lifter. Watch the device as
it elevates. If the lifter begins to tilt
forwards or backwards, return the lifter to
the ground and adjust bale position as
described in step 3. Raise the lifter again
to determine whether it is balanced. If
balance has been achieved, proceed to
the next step. Otherwise, try again to
balance the lifter. If the lifter cannot be
balanced, use another lifting device to
handle the load.
6. Stand behind the lifter. Grasp both operator handles and gradually begin pushing the lifter in the
necessary direction. Avoid sudden starts and stops.
7. Lower the lifter onto even, level ground. Make sure that the pallet and load are stable and entirely
supported by the ground.
8. Raise the lifter just enough to carefully withdraw the forks from the pallet. Before leaving the lifter,
lower it to the ground and disconnect the hoist chain/rope from the bale.
RECORD OF SATISFACTORY CONDITION (THE “RECORD”)
Record the condition of the lifter before putting it into regular service. Photograph and/or video the
unit. Include close range shots of all labeling, the forks, bale loops and pins, width adjustment pins,
height adjustment pins, and all welds. Measure the length and width of the bale opening. Record your
measurements. Write a description of the overall condition of the lifter. Collect your photos and/or
videos and writings in a file. Mark the file appropriately to identify it. The file is a record of the lifter in
satisfactory condition. Compare the results of all inspections to this RECORD to determine whether the
unit is in satisfactory condition. If the lifter is not in satisfactory condition, repair it before returning it to
service. Purely cosmetic changes, like damaged paint/powdercoat, do not constitute changes from
satisfactory condition. However, touchup paint should be applied to all affected areas as soon as
cosmetic damage occurs to prevent rusting and corrosion. If left unaddressed, rust/corrosion will
degrade the condition of the lifter and could make it unsafe to use.
LOAD TESTS
After creating a RECORD OF SATISFACTORY CONDITION and before using the lifter for the first
time, a qualified person should conduct a load test. The test load should be 125% of the rated load, i.e.
2000lb.x1.25 = 2500lb. (1136.4kg). Elevate the lifter a few inches above the ground. After a couple
minutes, return it to the ground and unload it. Perform a Monthly Inspection as described in
INSPECTIONS AND MAINTENANCE on p. 7. The (qualified) person performing the test must compose
a written report confirming the load rating of the lifter. The load rating should not be more than 80% of
the test load. The lifter must undergo load testing whenever it is repaired. Never modify the lifter without
first obtaining written approval from Vestil.
OLA-2-36/42-DLX
A
Bale pin
Bale
loop
A
B
B
Height adjustment pin
Front of
lifting arm
Fork
Operator
handle
Bekijk gratis de handleiding van Vestil OLA-2, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | OLA-2 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2199 MB |
