Vestil LPC-40 handleiding
Handleiding
Je bekijkt pagina 4 van 11
Table of Contents Rev. 6/1/2022 LPC, MANUAL
Table of Contents Copyright 2021 Vestil Manufacturing Page 4 of 11
(Continued from p. 4)
DO NOT exceed these usage parameters. Permanently remove the clamp from service before
exceeding the maximum number of load cycles.
• DO NOT elevate the lifter if the hoist rope/chain is kinked. Make sure that multiple part lines are not
twisted around each other before elevating the clamp and the load.
• DO NOT modify the product in any way without first obtaining written approval from Vestil.
Unapproved modifications automatically void the LIMITED WARRANTY (p. 11) and might make the
product unsafe to use.
• Avoid load swing by making sure the hoist rope/chain is vertical before raising the load.
• Carefully raise, lower, and move loads with the clamp. DO NOT start or stop suddenly. Sudden
stops/starts might induce load swing or disrupt the connection between the clamp and the sheet.
• DO NOT drag loads with the clamp.
• DO NOT remove or deface labeling on the clamp. DO NOT use the clamp UNLESS each label is in
place, undamaged, and easily readable from a reasonable distance. See LABELING DIAGRAM, p. 10.
• Inspect the product as instructed in INSPECTIONS AND MAINTENANCE on p. 9.
• DO NOT elevate the lifter any higher than necessary. Keep it as close to the ground as possible.
• DO NOT use the lifter if it is tagged “Out of service” or is otherwise designated as malfunctioning.
NATIONAL STANDARDS
LPC-series products are Below-the-Hook lifting (BTH) devices. They facilitate the handling of materials
in sheet form. American National Standard ASME B30.20 (the “Standard”) can be purchased online at
https://blog.ansi.org/2018/10/asme-b30-20-18-changes-below-hook-lifting/
. The Standard provides
inspection, testing, maintenance, and operation instructions for users of BTH devices. Acquire a copy of
the Standard. Apply all provisions that apply to Structural and Mechanical Lifting Devices. Contact local
occupational safety and health specialists to determine whether there are laws, ordinances, codes,
etc. (“authorities”) in addition to the Standard that apply to BTH devices in the location where the plate
clamp will be used. If content in this manual conflicts with provisions in authorities or the Standard, apply
the provisions from the authorities or Standard. Please contact Vestil’s
TECHNICAL SERVICE department
to report conflicts as soon as they are discovered.
MINIMUM UNIFORM LOAD WEIGHT & UNIFORM CAPACITY
In order for the clamp mechanism to securely attach to a sheet of material, a sheet of material must
weigh at least as much as the MINIMUM UNIFORM LOAD/PLATE WEIGHT
(MUPW) of the model of your
plate clamp. Do not attempt to lift a sheet if the sheet weighs less than the MUPW of your clamp. Do not
attempt to lift a sheet of material that exceeds the capacity of your clamp.
DIMENSIONS
MODEL
MINIMUM UNIFORM
PLATE WEIGHT
UNIFORM CAPACITY
LPC-20
400 lb. (181.8 kg)
2,000 lb. (909.1kg)
LPC-40
800 lb. (363.6 kg)
4000 lb. (1,818.2kg)
LPC-60
1,200 lb. (545 kg)
6,000 lb. (2,727kg)
B
A
C
D
E
MODEL
A
B
C
D
E
LPC-20
7
/
8
”
4
27
/
32
”
2
9
/
16
10
13
/
16
”
2”
LPC-40
1
3
/
16
”
6
1
/
8
”
3
1
/
8
”
12
13
/
32
”
2”
LPC-60
1
9
/
16
”
7
5
/
32
”
3
9
/
16
”
14”
2”
1” = 2.54cm 2.2 lb. = 1kg
Dimensions are subject to change without notice.
Measure dimension A after you receive your unit and
include it in the
RECORD OF SATISFACTORY CONDITION
on p. 8.
Bekijk gratis de handleiding van Vestil LPC-40, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | LPC-40 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4903 MB |
