Handleiding
Je bekijkt pagina 18 van 19
TABLE OF CONTENTS Rev. 10.5.2022 LAD-RAF, MANUAL
TABLE OF CONTENTS Copyright 2022 Vestil Manufacturing Page 18 of 19
and chain are undamaged and securely fastened to the guard railing. Snap hooks should close
automatically.
• Axle, axle receiver/back leg weldment and wheels: Make sure that the back leg weldment is
undamaged, e.g. not bent, cracked, or warped. Check the wheels. They must not be cracked or
significantly worn. Wheels should be vertical (not angled towards or away from the ladder) and should roll
smoothly. Make sure that the axle and the axle receiver are undamaged. The wheel retaining cotter pins
must be securely fastened to the axle.
• All frame members (step weldment, back leg weldment, base supports, handrails) and all fasteners (bolts,
nuts, pins): Inspect each frame member weekly for damage like excessive wear, warps, cracks, and other
types of damage. All frame pieces should be square, rigid, and free of rust and corrosion. Remove rust
with steel wool or a metal bristle brush and apply touch-up paint to the affected area. Check the areas
where frame members are bolted together. Check the areas around bolt holes for warps, cracks, etc.
Replace all parts that are damaged before using the ladder again.
• Square (rubber) caps: Check the caps for cracks, tears, wear, or for the bottoms of the front legs cutting
through the caps. Install replacement caps before returning the ladder to service. Even a moderate
amount of wear can affect the ability of a cap to resist sliding movement. The entire bottom surface of
each cap must contact the floor.
• Outriggers (11 and 12 step models): Examine the outriggers and confirm that they are securely fastened
to the step weldment. Both outriggers should make solid contact with the ground, i.e. the ladder should
not be able to wobble. Confirm that the caps on the outrigger legs are in satisfactory condition.
Maintenance: in addition to correcting issues discovered during inspections, maintain the ladder
as described below.
• Clean the ladder to remove dirt and grime, especially from step surfaces.
• Lubricate the axle as necessary for the wheels to rotate freely.
• Apply touchup paint wherever the finish is chipped.
LABELING DIAGRAM
Each unit should be labeled as shown in the diagram. Label content and location are subject to
change so your product might not be labeled exactly as shown. Compare the diagram below to your
RECORD OF SATISFACTORY CONDITION
. If there are any differences between actual labeling and this
diagram, contact TECHNICAL SERVICE.
Replace all labels that are damaged, missing, or not easily readable (e.g. faded). To order
replacement labels or to inquire whether your unit is properly labeled, contact the technical service
and parts department online at https://www.vestil.com/page-parts-request.php
or by calling (260)
665-7586 and asking for the Parts Department.
B: Label 1153
C: Label 729A
A: Label 740
D: Label 821
A
B
C
D
NOTE: To provide access to this manual for all persons who use
this ladder, a protected copy of the manual should be attached
to the ladder. For example, a copy of the manual can be
placed inside a transparent plastic pouch or folder that is tied to
the ladder frame. An appropriate place to tie the folder to the
frame is on the side rail next to the step where label 821 is
applied.
Bekijk gratis de handleiding van Vestil LAD-RAF-12-24-P-EZ, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | LAD-RAF-12-24-P-EZ |
| Categorie | Ladder |
| Taal | Nederlands |
| Grootte | 7045 MB |
