Vestil FL-4000-N handleiding
Handleiding
Je bekijkt pagina 5 van 8
Table of Contents Rev. 8/21/2020 FL-4000 MANUAL
Table of Contents Copyright 2020 Vestil Manufacturing Corp. Page 5 of 8
NATIONAL STANDARDS
US OSHA Rule 1910.178 (29 CFR 1910.178; the “Rule”) classifies this device as a (lift truck) “front- end
attachment” whenever it is mounted on a lift truck. The Rule incorporates American National Standard
ANSI/ITSDF B56.1 (the “Standard”). The current revision of the Standard is published by the Industrial Truck
Standards Development Foundation on its website (www.itsdf.org
) where it is freely downloadable at
http://www.itsdf.org/cue/b56-standards.html. Before putting this device into service, acquire a copy of the
Standard. Apply all relevant parts of Part II: For the User. If instructions provided in this manual conflict with the
Standard, then apply the instructions in the Standard. Vestil requests that you immediately share your discovery
of any such conflicts with personnel of its
TECHNICAL SERVICE department. Contact information for
TECHNICAL SERVICE appears on the cover page of this manual.
USING THE LOADER
DO NOT wrap the release cable around any part of your body, especially your hands, or
attach the handle at the end of the cable to your clothing. If you do and the chute is released, you might be
seriously injured.
Before mounting the loader on the forks of your lift truck, confirm that the chute is latched to the base frame
(cannot rotate).
Step 1: Drive the lift truck forward and insert the forks into the fork tubes. Drive as far forward as possible. The
tips of the forks will press against the ends of the fork tubes.
Step 2: Attach the safety chain to the fork carriage. Wrap the chain around part of the fork carriage. Connect the
quick link (at the free end of the chain) to a link in the chain with as little slack as possible.
Step 3: Unlock the latch lever by pulling the
finger tab until the lock disengages the latch bar
(see diagram).
Step 4: The loader is equipped with a release cable and
handle. This feature allows the forklift operator to release the
chute without having to dismount the forklift. Store the handle
within reach
from the cab. For example, hook the handle to
the roll cage of the cab.
Make sure plenty of slack is in the
cable to avoid accidentally releasing/dumping the chute.
Step 5: Fill the loader with material, e.g. snow, sand, gravel,
by driving it into the material. Tilt the forklift mast toward the
cab and raise the forks. Only raise the forks as high as
necessary for adequate ground clearance.
Step 6: a) To dump material into a receptacle, raise the forks
above the side of the receptacle (e.g. dumpster) a
nd drive
forward until the side of the dumpster is directly beneath the
middle of the chute. Lower the loader until the chute rests on
the side of the dumpster. b) To dump contents onto a
material pile, set the chute on top of the pile.
Step 7: Dump the chute by pulling the release cable. NEVER
wrap the release cable around your fingers, hand, etc.
Slowly raise the forks to allow the chute to tilt forward. Stop
pulling the cable as the carrier begins to tilt forward. Slowly
drive forward while raising the
forks to allow the chute to
dump completely.
Step 8: Return the chute to the latched position. Back away
from the receptacle/material pile. Lower the forks until the lip
of the chute contacts the ground. Slowly drive in reverse
while continuing to lower the forks. You should hear the
chute latch to the base.
Step 9: Level the mast. Confirm that the chute is latched to
the base by raising the forks. The chute should not
rotate/dump. If necessary, lower the forks completely and
manually latch the chute to the base by pressing down on the
rear wall of the chute until the latch lever engages the latch
bar. Secure the latch by pressing the latch lock over the latch
bar.
Release cable with handle
Latch
lever
Latch lock
Finger tab
Latch bar
Bekijk gratis de handleiding van Vestil FL-4000-N, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | FL-4000-N |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 2307 MB |
