Vestil EPT-2547-30 handleiding
Handleiding
Je bekijkt pagina 55 van 58
TABLE OF CONTENTS 5/19/2022 EPT MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Page 55 of 58
RECORD OF SATISFACTORY CONDITION (THE “RECORD”)
Before putting this machine into service, make a record of its appearance and operation. Photograph the unit from
multiple vantage points with the forks in both the lowered and fully elevated positions. Take close range photographs
of all labeling applied to the machine, the drive wheel(s), casters, and rollers, control yoke and all control buttons,
switches, and gauges, the hydraulic cylinder, and both forks. Remove the yellow cover and photograph the internal
components. Use the control buttons to raise and lower the forks. Describe the motion of the forks as they elevate and
descend, e.g. smoothly and evenly from side-to side without binding or lurching. Describe the sounds made by the
machine as the cylinder extends and retracts to lift and lower the forks. Collect all photographs and writings into a file.
Mark the file appropriately to identify it. This file is a record of the unit in satisfactory condition (the “Record”).
Compare the results of all inspections to this RECORD to determine whether the pallet truck is in satisfactory
condition. Do not use the truck unless it is in satisfactory condition. Purely cosmetic changes, like damaged paint or
powdercoat, are not changes from satisfactory condition. However, touchup paint should be applied as soon as
damage occurs.
INSPECTIONS & MAINTENANCE
Regular inspections and maintenance are necessary to keep the device in satisfactory condition. Compare the results
of each inspection to your RECORD
to determine whether the unit is satisfactory condition or requires repairs or
replacement parts. If you are uncertain whether a part requires repair or replacement, contact TECHNICAL SERVICE for
assistance.
• Periodically lubricate moving parts.
• Keep the product clean and dry.
• Only use manufacturer- approved replacement parts.
INSPECTIONS:
• DO NOT use brake fluid or jack oil in the hydraulic system. If oil is needed, use an anti-wear hydraulic oil,
viscosity grade 150 SUS at 100°F, (ISO 32 @ 40°C), or a non-synthetic transmission fluid.
• Only use replacement parts either supplied or approved by the manufacturer.
Only trained, qualified persons should perform inspections or maintenance on this pallet truck. Perform a Before
Each Use inspection before the truck is used for the first time and before each subsequent use.
If your truck is rarely used (1-2 times per month), inspect the unit at least once per month, or before each use,
whichever is more frequent.
Before each use, inspect the truck for the following:
1. Frayed wires;
2. Oil leaks;
3. Pinched or damaged hoses;
4. Structural damage: cracked welds, warping or other deformation of the cylinder brackets, forks, front rollers or
drive wheel(s), handle, or the housing that protects the electrical components;
5. Proper function of all limit switches;
6. Proper horn operation;
7. Battery: clean, not leaking electrolyte solution, secure connections with both terminals. Also make sure that the
battery is immobilized so that it cannot move during operation.
8. Proper rotation of all wheels, casters, and rollers.
At least once per month, disconnect the battery, chock the wheels, and inspect the following:
1. Oil level: raise the forks to the maximum height; when the cylinder(s) are properly filled, the oil level should be 1-
1/2 to 2 inches below the reservoir fill hole. Return the forks to the fully lowered position.
2. Damage to or excessive wear of:
a. Pivot points;
b. Hydraulic hoses;
c. Electric wires;
d. Retaining rings and/or pins for the rollers, drive wheels, and all pivot points;
e. Bearings
3. Wobbliness or looseness of rollers and/or drive wheels;
4. Proper function of the hand or foot actuated mechanisms;
5. Proper battery water level;
6. Unusual noise or abnormal movement during operation;
7. Legibility and undamaged condition of all product labels.
Bekijk gratis de handleiding van Vestil EPT-2547-30, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | EPT-2547-30 |
| Categorie | Vorkheftruck |
| Taal | Nederlands |
| Grootte | 48560 MB |
