Vestil EPT-2047-30 handleiding
Handleiding
Je bekijkt pagina 20 van 58
TABLE OF CONTENTS 5/19/2022 EPT MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Page 20 of 58
Casters might become stuck in gaps or cracks in the surface, which could cause the EPT to stop
suddenly. A sudden stop can cause the load to shift and the load and truck might tip over.
2. INSPECT THE EPT & PERFORM A FUNCTIONS TEST
Inspection Prior to Use:
Always inspect the unit before you use it.
Begin the inspection by removing all debris found on the surface of the
forks; then
a. Check the forks for deformations and cracks;
b. Check the floor beneath the truck and the truck itself for leaked hydraulic fluid or battery acid.
DO NOT use the EPT if you discover any damage or abnormalities. Tag the unit “Out-of-Service”
and report all problems to authorized maintenance personnel.
Functions TestS (Refer to FIG. 11 on p. 19)
Verify that all powered functions work properly.
1. Raise the forks to the maximum elevation;
2. Return the forks to the lowest position.
3. Raise the forks again. While raising them, press the E-stop button. The forks should immediately stop
moving. Reset the E-stop by returning the control yoke to either position 1 or 3. See
OPERATING THE
EPT, Step 3 (below). Pull the red E-stop button up/out.
4. Fully raise the forks, and while lowering the forks press the E-stop. The forks should immediately stop
moving. Reset the E-stop.
5. Drive the EPT in reverse at low speed. While driving press the belly switch. The machine should
immediately move in the opposite direction for ~3 seconds and then stop. Reset the control yoke.
6. Drive the EPT in both the forward and reverse directions for a few seconds.
7. Test the horn.
8. Verify that the control yoke automatically returns to the vertical position when released. See
OPERATING
THE EPT, Step 3 (below).
Only use the pallet truck if it is in SATISFACTORY CONDITION. See
RECORD OF
SATISFACTORY CONDITION. If malfunctions occur, park the truck in a safe location, tag it “Out-of-Service” and
then report the malfunctions to qualified maintenance personnel.
Operating the EPT
Step 1: Turn on the power. See “Power” callout box on p. 19
.
Step 2: Pull the red E-Stop button up to disengage the service brake.
Step 3: Tilt the control yoke to the drive position (2), which is shown
to the right.
NOTE: The EPT uses magnetic brakes which engage when the handle
is in or near either of the neutral positions (1 and 3).
The yoke is designed to automatically return to neutral position (1)
after the handle is released; therefore, the brakes will engage
automatically as well.
Step 4: Rotate the movement control wheel in the appropriate direction to drive forward or in reverse. See
“Movement Controllers” text box and the corresponding photo in FIG. 11 on p. 19.
1 = Neutral
2 = Drive
3 = Neutral
USING THE EPT
EPT-series
electric-hydraulic
pallet
trucks
are
type
E
powered
industrial
trucks.
Operation,
inspections,
maintenance, and storage
of the truck must conform to provisions of
US OSHA General Industry rule 1910.178
applicable
to
type
E
powered
industrial
trucks
as
well
as
to
applicable
provisions
of
the
latest
revision
of
ANSI/ITSDF B56.1. A copy of the standard is freely downloadable from the ITSDF website (
www.ITSDF.org).
1
.
DETERMINE
CONDITION
OF
FLOOR
OR
OTHER
SUPPORTING
SURFACE:
Inspect
the
floor
(or
other
surface;
for
example
a
parking
lot,
dock
board
or
dock
leveler)
prior
to
use.
The
supporting
surface
must
be
smooth and dry
so choose a route that avoids obstacles, spills, and surface damage.
Bekijk gratis de handleiding van Vestil EPT-2047-30, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | EPT-2047-30 |
| Categorie | Vorkheftruck |
| Taal | Nederlands |
| Grootte | 48560 MB |
