Vestil BTC-CART handleiding
Handleiding
Je bekijkt pagina 9 van 11
TABLE OF CONTENTS Rev. 6/8/2022 BTC-CART, MANUAL
TABLE OF CONTENTS Copyright 2021 Vestil Manufacturing Corp Page 9 of 11
b) Mount the cart on the forks of your lift truck. Insert the forks through the fork channels. Drive forward
until the fork tips gently contact the front plate of the cart. Wrap the carriage strap around the carriage
of your fork truck without slack. Attach the hook to the strap or to carriage. Elevate the forks. Do not
raise the forks any higher than necessary. Start slowly and accelerate gradually. Turn and stop very
carefully. Loads applied to the rollers will tend to move forwards, i.e. against the load restraint bar, as
you slow down or turn. Before leaving the cart unattended, lower it to the ground and apply both
caster brakes.
RECORD OF SATISFACTORY CONDITION
Before the cart is put into service, make a written record of its condition. Include
observations of all features, i.e. rollers, load restraint bar and linkages, casters, caster brakes,
carriage/safety strap and hook, the supporting frame, welds, handle, and (if applicable)
winch mount bracket and all parts of the winch (cable, spool, hook, etc.). Thoroughly
photograph the unit and all labels applied to it. Describe where each label is located. Collect
all writings and photographs in a file. Your file is a record of the unit in satisfactory condition.
Compare the results of all inspections to your record to determine if the unit is in satisfactory
condition.
INSPECTIONS & MAINTENANCE
NOTICE
Proper use, maintenance, and storage are essential for this product to function properly.
o Inspect the unit as instructed and at least as frequently as instructed.
o Use, inspect, and maintain this cart as instructed in the current revision of ANSI/ITSDF B56.1.
o Store the unit in a dry location.
Compare the results of each inspection to your RECORD OF SATISFACTORY CONDITION to determine
whether the unit is in satisfactory condition. DO NOT use the cart unless it is in satisfactory condition.
Clean the cart with a mild soap & water solution. Only use manufacturer-approved replacement parts
to restore the unit to satisfactory condition. Never make temporary repairs of damaged or missing parts.
DON’T GUESS! If you have any questions about the condition of your unit, contact the TECHNICAL
SERVICE department. The phone number is provided on the cover page of this manual. Purely cosmetic
changes, such as chipped paint, are not changes from satisfactory condition. However, touchup paint
should be applied to all areas where the finish is damaged as soon as damage occurs to prevent rust
formation. Left unaddressed, rusting could compromise the soundness of the metal and create a safety
hazard.
Inspect the following before each use:
1. Carriage/Safety strap and snap hook: Confirm that the safety strap and hook are in satisfactory
condition. The spring latch (of the hook) should automatically close and remain closed unless
deliberately opened. Look for strap fraying, cuts, burns, tears, etc. Replace the strap if any cut or tear or
other damage extends across 25% of the strap width or more.
2. Labeling: All labels should be easily readable and in place as shown in the LABELING DIAGRAM
on p.
10. If a label is damaged, not easily readable, or missing, contact TECHNICAL SERVICE to order a
replacement.
Inspect the following at least 1 time per month:
1. Fasteners (hardware): Confirm that all bolts, nuts, washers, pins, cotter pins, etc. and securely
fastened. Tighten loose connections. If a lock nut is removed for any reason, it must be replaced with a
new lock nut.
2. Frame elements: Confirm that the frame is structurally sound and free of rust. The frame must be
square and rigid. Look for bends, cracks, rust, and corrosion. Confirm that all welds are intact. Remove
dirt & debris. Apply touchup paint to area where the finish is damaged. Make sure that the load restraint
bar and its linkages are securely attached to the frame. Look for bends, cracks, and other damage.
3. Rollers: Confirm that each roller is able to rotate freely and smoothly, is securely attached to both
side of the frame, and is undamaged.
4. Casters: Examine each caster for significant wear, wobbling, deformations, warps, cracks, and other
forms of damage. Confirm that caster brakes work properly. Apply the brakes and confirm that the cart
cannot move without significant effort.
Bekijk gratis de handleiding van Vestil BTC-CART, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | BTC-CART |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 3527 MB |
