Vestil AHA-2-12-10-ALO handleiding
Handleiding
Je bekijkt pagina 21 van 24
Table of Contents Rev. 12/9/2019 AHA MANUAL
Table of Contents Copyright 2019 Vestil Manufacturing Corp. Page 21 of 24
USING THE CRANE
Before using the crane for the first time: 1) Perform a “Before and after each use” inspection (INSPECTIONS &
MAINTENANCE, part A, p. 22); and 2) Conduct a load test (INSPECTIONS & MAINTENANCE, part C, p. 22).
Operate the crane in a safe manner to reduce the risk of serious personal injuries or death.
• Only use this crane if you are qualified and trained to use it. The operating instructions in this manual supplement
safe crane and hoist operation practices applied at your work site. Acquire a copy of the most recent edition of ASME
B30.17 and apply all operation, inspection, maintenance, and care recommendations.
• ALWAYS apply the safe material handling practices learned from your training program.
• All personnel not participating in the use of the crane must stay out of the area during use. Be certain no part of any
person or object is under any part of the boom (I-beam) or the suspended load at any time and particularly before
lowering it. Instruct all persons to remain at a safe distance during operation.
• Always carefully watch the boom and any load hanging from it while using the crane.
• Always follow the hoist and trolley manufacturers’ instructions regarding proper use of their products.
• BEFORE the load is connected to the hoist, lock or immobilize the casters, for example with chocks.
• Only use this crane on level concrete (or equal) surface.
• DO NOT use the crane and notify your supervisor and authorized maintenance personnel if: 1) you observe any
damage or hear unusual noise during operation; or 2) you observe any warping or deformation of the I-beam, the
adjustable uprights, the load hook or hoist chain/cable.
• DO NOT operate a hoist with a twisted, kinked, or damaged chain or rope. DO NOT operate a rope hoist unless the
rope is properly seated in its groove.
This crane can be used outdoors. However, it should be sheltered from the weather when not in use.
LOADING THE CRANE
Position the trolley and hoist directly above
the load. Center the trolley and hoist above the
center of the load and position the long axis of
the I-beam above the center of the load. Proper
positioning is illustrated in Diagrams 8A & 8B.
Connect the load to the hoist chain/cable,
according to the instructions supplied with your
hoist and the method applied at your work site;
then raise the load only as high as is necessary
to position it. Once the load is properly
centered above the work location, lower the
load until it is fully supported by the ground or
work surface and disconnect the load from the
hoist. Return the crane to its storage locations.
If you must move the load to a different
location, return the load to the ground or other
supporting surface, e.g. pallet, and disconnect
it from the hoist. Move the crane and load
separately to the work location. Only use
the crane to lift loads.
If your crane is equipped with V-Groove
casters (option AHA-2/4-V or AHA-2/4-V4) and
V-Track is installed, the crane can be moved on
the track while loaded. The hoist must be
immobilized and the load lowered. Push the
trailing end of the crane, not the load.
RECORD OF SATISFACTORY CONDITION (THE “RECORD”)
Thoroughly inspect the crane after assembling it and before putting it into service. Record the condition and
appearance of each of the frame members (I-beam, tube weldments, yokes, uprights), the wheels and/or casters,
beam clamp, and all fasteners (bolts, nuts, etc.). Thoroughly photograph the crane from multiple angles. Include close
range photographs of the casters and/or wheels, all labeling, and all beam clamp connections. Add the photographs
to the record. Collate all photographs and writings into a single file. This file is a record of the crane in satisfactory
condition. Compare the results of all INSPECTIONS to this Record to determine whether the crane is in satisfactory
condition. Do not use the crane unless it is in satisfactory condition. Purely cosmetic changes, like damaged paint or
Diagram 8B: Center the long
axis of the I-
beam above the
center of the load.
Diagram
8A:
Center hoist above
center of load
Properly centered load
Improperly centered load
Hoist
Hoist
Load
Hoist &
trolley
Load
Load
Hoist &
trolley
Hoist
chain/rope
I-beam
I-beam
Properly centered I-beam
Improperly centered I-beam
Load
Load
Bekijk gratis de handleiding van Vestil AHA-2-12-10-ALO, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Vestil |
| Model | AHA-2-12-10-ALO |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6717 MB |
