Varytec Hero Pixel Wash 760FX handleiding

Verlichting

Varytec

32 pagina's

PDF beschikbaar

Handleiding

CAUTION!

Risk of injury due to unexpected movements of the device!

The device head may perform fast movements and generate very bright light. This is the case immediately after the device is

switched on, in automatic or remote operation, and when a connected DMX controller is switched o. Persons who are in the

immediate vicinity of the device may be injured or frightened by this. Make sure that there are no obstacles within the movement

range of the mirror, and that no persons are in the immediate vicinity of the head before switching it on and during its operation.

Switch o the device before any work is performed in the movement range or immediate vicinity of the device, or if unauthorised

persons are in that area.

NOTICE!

Risk of re due to covered vents and neighbouring heat sources!

If the vents of the device are covered or the device is operated in the immediate vicinity of other heat sources, the device can

overheat and burst into ames. Never cover the device or the vents. Do not install the device in the immediate vicinity of other

heat sources. Never operate the device in the immediate vicinity of naked ames.

NOTICE!

Damage to the device if operated in unsuitable ambient conditions!

The device can be damaged if it is operated in unsuitable ambient conditions. Only operate the device indoors within the

ambient conditions specied in the “Technical specications” chapter of this user manual. Avoid operating it in environments

with direct sunlight, heavy dirt and strong vibrations. Avoid operating it in environments with strong temperature uctuations. If

temperature uctuations cannot be avoided (for example after transport in low outside temperatures), do not switch on the

device immediately. Never subject the device to liquids or moisture. Never move the device to another location while it is in oper‐

ation. In environments with increased dirt levels (for example due to dust, smoke, nicotine or mist): Have the device cleaned by

qualied specialists at regular intervals to prevent damage due to overheating and other malfunctions.

NOTICE!

Damage to the device due to high voltages!

The device can be damaged if it is operated with the incorrect voltage or if high voltage peaks occur. In the worst case, excess

voltages can also cause a risk of injury and res. Make sure that the voltage specication on the device matches the local power

grid before plugging in the device. Only operate the device from professionally installed mains sockets that are protected by a

residual current circuit breaker (FI). As a precaution, disconnect the device from the power grid when storms are approaching or it

the device will not be used for a longer period.

NOTICE!

Risk of re by exceeding the maximum current!

The device can supply power to other devices of identical design and connected in series. If too many devices are connected, the

maximum permitted power consumption can be exceeded, which can cause the device to overheat and burst into ames. Only

connect devices of identical design to the device. When deciding how many devices you can connect in series, make sure that the

maximum output current specied on the device and in the “Technical specications” chapter of the user manual is not

exceeded. Only use power cords with a cable cross-section designed for the required current intensity when connecting the

devices in series.

NOTICE!

Possible staining due to plasticiser in rubber feet!

The plasticiser contained in the rubber feet of this product may react with the coating of the oor and cause permanent dark

stains after some time. If necessary, use a suitable mat or felt slide to prevent direct contact between the device’s rubber feet and

the oor.

NOTICE!

Risk of overheating and re due to inadequate distance and bad ventilation!

If the distance between the light source and the illuminated surface is too short or the device is badly ventilated, the device can

overheat and cause res. Make sure that illuminated surfaces are more than 2 m away. Do not operate the device in ambient

temperatures above 40 °C. Always ensure sucient ventilation at the operating location.

NOTICE!

Risk of re due to installation of a wrong fuse!

Using fuses of a dierent type than compatible with the device may cause a re and seriously damage the device. Only use fuses

of the same type. Observe the labelling on the device casing and the information in the "Technical data” chapter.

Safety instructions

Hero Pixel Wash 760FX

Moving Head

Bekijk gratis de handleiding van Varytec Hero Pixel Wash 760FX, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.