Handleiding
Je bekijkt pagina 83 van 133
Network Settings
User Guide 79
Root Certificate
Displays whether the certificate is active. Root Certificate 1 Subject through Root
Certificate 5 Subject are displayed. Configure the device certificate on the Certifi-
cates page.
IPSec Rules
Allows to validate the rule used for communication using the IPSec protocol. Rule 1
through Rule 10 are displayed. To activate this item, click Settings button and con-
figure the following on the IPSec Rule Settings page.
1. Policy
Rule: Select whether the rules for IPSec communication are used or not.
Key Management Type: Select a type of the key used for the rule from IKEv1,
IKEv2, and Manual.
Encapsulation Mode: Transport encapsulates an encrypted data and transmits
along with an IP header. This is the simplest method when both the transmitting
host and receiving host have the IPSec protocol supported. Tunnel uses a gate-
way provided in the network. The gateway receives the IP packets sent by the
transmitting host, encrypt the entire IP packet which is then encapsulated by
IPSec, then transmits along with a new IP header.
Select whether the rules for IPSec communication are used or not.
2. IP address
IP Version: Specifies the IP version of the other end. Select IPv4 or IPv6.
IP Address (IPv4): Specifies the IPv4 addresses of the hosts or network with
which the machine is connecting via IPSec. When you are restricting the scope of
IPSec, be sure to specify the IP addresses. If this field is blank, all IPv4 addresses
will be allowed to connect the machine.
Subnet Mask: When IPv4 is selected for IP Version, this specifies the subnet
mask of the hosts or network with which the machine is connecting via IPSec. If
this field is blank, the specified addresses are considered to be host addresses.
IP Address (IPv6): Specifies the IPv6 addresses of the hosts or network with
which the machine is connecting via IPSec. When you are restricting the scope of
IPSec, be sure to specify the IP addresses. If this field is blank, all IPv6 addresses
will be allowed to connect the machine.
Prefix Length: When IPv6 is selected for IP Version, this specifies the prefix
length of the hosts or network with which the machine is connecting via IPSec. If
this field is blank, the specified addresses are considered to be host addresses.
Remote Peer Address: If Tunnel is selected in Encapsulation Mode, assign an
IP address that is remotely controlled.
3. Authentication: Configures the local side authentication when IKEv1 is selected
as Key Management Type. To set a character string as the shared key and use it
for communication, select
Pre-shared Key an
d enter the string of the pre-shared
key in the text box. To use the CA-issued Device Certification or Root Certificate,
select the Certificates. When Certificates is selected, the availability of the
device certificate is shown. To make advanced settings, click Settings button and
select a certificate. Configure the device certificate on the Certificates page of
Security Settings.
Configures the local side and remote side authentication when IKEv2 is selected
as Key Management Type. Configure Authentication Type, Local ID Type,
Local ID, Device Certificate and Pre-shared Key on Local Side, and Authenti-
cation Type, Remote ID Type, Remote ID and Pre-shared Key on Remote Side.
4. Key Exchange (IKE phase1): When using IKE phase1, a secure connection with
the other end is established by generating ISAKMP SAs. Configure the following
items so that they meet the requirement of the other end.
Mode: Configures this item when IKEv1 is selected as Key Management Type.
Main Mode protects identifications but requires more messages to be exchanged
with the other end. Aggressive Mode requires fewer messages to be exchanged
with the other end than Main Mode but restricts identification protection and nar-
Bekijk gratis de handleiding van UTAX 5009ci, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | UTAX |
| Model | 5009ci |
| Categorie | Printer |
| Taal | Nederlands |
| Grootte | 11339 MB |
