Tryton TJS40 handleiding
Handleiding
Je bekijkt pagina 10 van 72
10
- Emission dust hazardous for human health when works are carried out The above-mentioned causes may lead to higher exposure to vibrations
in closed rooms (confined areas).
during the whole work time.
One must implement additional safety measures to protect the operators
from exposure to vibrations, such as maintenance of the electric tool and
Cordless angle grinder
work tools, assurance of proper hand temperature, or determination of
the sequence of work operations.
The declared total vibrations and declared noise emissions were
measured in accordance with a standard test method and may be used
for tool comparison.
The declared total vibrations and noise emissions can be used in
preliminary exposure assessment.
Warnings:
Operating instruction
The vibrations and noise emissions during the actual use of the power
tool may differ from the declared values depending on how the tool is
The numbering of device elements refers to the drawing on pages 2-4 of the
used and on the type of the workpiece in particular.
instruction manual:
Determine safeguards to protect the operator. They should be based on
Fig.
the estimated exposure under actual operational conditions (taking into
account all parts of the operating cycle such as when the tool is switched
Cover clamp
off or idle except the start time).
Before each use, check that the moving parts of the device are
operating correctly and are not blocked, cracked or damaged, which
Battery*
could affect the proper functioning of the device. Repair a damaged
Battery lock button*
tool before use.
Fig. Battery level indicator button*
Before connecting the battery, make sure that the grinder switch (6)
Battery level indicator*
is in the off position.
Charger*
n Charging the battery
NOTE! Battery and charger are not part of the delivery. Depending on your
Fig.
needs, you can purchase a 1.5 Ah battery TJ15AK, 2.0 Ah battery TJ2AK or
4.0Ah TJ4AK and a compatible charger TJ3LD (charging time 3–5 hours)
or TJ1LD (charging time 1 hour).
(see Fig. B, page 2)
* The accessories shown or described are not standard equipment.
Charge the
For the complete offer of auxiliary equipment, see our catalogue.
battery fully before use.
TJ3LD
The first charging procedure using TJ3LD should last at least 5 hours.
1. Press the battery lock button (8) and remove the battery (7) from the
angle grinder (see Fig. A, page 2).
2. (7) (11) (see Fig. B, page 2).
3.
4. (12)
TJ1LD
The first charging procedure using TJ1LD should last at least 1 hour.
1. Press the battery lock button (8) and remove the battery (7) from the
angle grinder (see Fig. A, page 2).
2. (7) (11) (see Fig. C, page 3).
3. Connect the charger plug to a mains socket (220–240 V, 50 Hz).
n
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
maintained properly, the vibration level may differ from the values given.
THE SET CONTAINS:
ź - 1piece
ź Disk guard - 1 piece
ź Side handle -1 piece
ź Fixing flange -1 piece
ź Compression nut -1 piece
ź Pin wrench -1 piece
ź Disk -1 piece
ź Warranty card -1 piece
ź -1 piece
n Device components
A: 1. Side handle
2. Disk guard
3.
4. Rotation direction arrow
BEFORE YOU START WORKING:
5. Spindle lock button
1.
6. On/off switch
7.
8.
B: 9.
2.
10.
11.
12. Adapter*
F: 13. Spindle
14. Fixing flange
15. Disk
16. Compression nut
You can check the battery level with the battery level indicator button
17. Pin wrench
A single LED means the battery level is low, two LEDs
mean medium level, and three LEDs mean full battery.
TECHNICAL DATA:
Connect the battery to the charger
Connect the adapter plug to the charger .
Connect the adapter to a mains socket (110–240 V, 50-60 Hz).
Connect the battery to the charger
Battery charging indicator
A green LED light indicates that the charger is connected to a power
source. After the battery is connected, the red LED is on to indicate
charging. Blinking green battery LEDs also indicate that the battery is
charging and show the current battery level.
(9)
.
Charger
Charger
MODEL J T S40
Supply voltage 20V d.c.
Rotational speed 8000 /min
Max. disk diameter/ hole diameter 115 mm / 22 mm
Spindle thread M14
Weight (with battery) 1,9 кg
Acoustic pressure level(LpA) 75,7 dB(A)
Acoustic power (LwA) 86,7 dB(A)
Vibration level acc. to EN 60745-2-3
main handle a
h,AG
tolerance of measurements
2
( - 1,5m/s )
2
5,642 m/s
Tolerance of measurements K ,K
LpA LwA
3 dB(A)
Recommended 20 V Li-ion batteries: TJ15AK (1,5Ah), TJ2AK (2Ah), TJ4AK (4Ah)
Recommend chargers: TJ3LD(3-5h), TJ1LD (1h)
Bekijk gratis de handleiding van Tryton TJS40, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Tryton |
| Model | TJS40 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 14905 MB |
