Troy-Bilt Mustang Z42E XP handleiding
Handleiding
Je bekijkt pagina 14 van 88
14
OPERATION
3. LCD Screen & Battery Level Indicator - Located on the
VCM, the LCD display & battery level indicator are used
to provide instructions, warnings and information about
your tractor systems and the battery level of your tractor.
4. PTO (Blades ON/OFF) Button - Located on
the VCM, the PTO button is used to operate the
blades. To engage the cutting deck (blades ON),
press and hold the PTO button for three seconds.
The yellow indicator light around the PTO button is ON
Pressing the PTO button again will disengage the cutting
deck (Blades OFF). The yellow indicator light around the
PTO button is OFF.
5. Eco Mode Button - Eco mode slightly
reduces blade speed to increase battery run
time of the tractor in areas of low grass load.
6. Low Speed Precision Drive Button -
Low speed precision drive enhances
maneuverability and control by setting
maximum forward speed to 4 mph
and is recommended when
loading/unloading the tractor on a
trailer, mowing on rough terrain,
around a perimeter, and in tight
spaces.
7. Headlight Button - Located on the VCM the
headlight button is used to turn the headlights on
or off.
D. MULTITOOL IF EQUIPPED
The multi-tool (a) is located on the front of the right console
(E1, Figure 14) or on the top, rear of the left console (E2, Figure
14). The multi-tool (a) can be used as a deck lift lockout, to
remove the footpan bolt, adjust the height of the lapbar drive
control levers, drive control lever stop adjustment and can be
used as a removal tool with the 1/2” socket end. See the Service
and Maintenance section for more information on multi-tool
(a) usage.
E. BRAKE PEDAL
The brake pedal is located in the center of the tractor, in front
of the floor pan. The brake pedal can be used for stopping the
tractor or setting the parking brake.
Setting The Parking Brake
1. Push the brake pedal (a) all the way forward (Figure 17).
2. Rotate the brake pedal pad (b) forward to engage the
parking brake latch (c).
3. Ensure the brake pedal pad is fully engaged with the
parking brake latch.
4. To disengage the parking brake, push the brake pedal (a)
forward.
C. VEHICLE CONTROL MODULE VCM
WARNING
Never leave a running tractor unattended. Always
disengage PTO, set parking brake, stop tractor and
remove the key to prevent unintended starting.
The vehicle control module (VCM) is located on the right console.
The VCM (Figure 15) is the location of several control buttons
for your tractor. The VCM includes the START/STOP button, PTO
(blades ON/OFF) button ,Eco Mode Button, Headlight Button,
Low Drive Speed Button, LCD Screen and the Battery Level
Indicator.
1
2
3
4
5
6
7
Figure 15
WARNING
Prior to operating the tractor, refer to both Safety
Interlock System and Starting The Tractor in the
Operation section of this manual for detailed instructions
regarding the VCM and operating the tractor.
1. Start/Stop Button - Located on the VCM,
the start/stop button is used to start and stop
the tractor. While active, the start/stop button
indicator ring is illuminated blue.
2. Key Switch - The key switch is located in the center
of the VCM and powers the VCM when the key is fully
inserted. The tractor cannot be started unless the key is
fully inserted and the START/STOP button is depressed.
Removing the key turns the tractor off (Figure 16).
Figure 16
Bekijk gratis de handleiding van Troy-Bilt Mustang Z42E XP, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Troy-Bilt |
| Model | Mustang Z42E XP |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 13095 MB |
