Toolson WS4100 handleiding

Niet gecategoriseerd

Toolson

248 pagina's

PDF beschikbaar

Handleiding

/ 248

Je bekijkt pagina 25 van 248

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58  www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

25GB

Faulty electrical connecting leads such as these may

not be used and are highly dangerous due to the in-

sulation damage.

Check electrical connecting leads regularly for dam-

age. Ensure that the connecting lead is not attached

to the mains supply when you are checking it.

Electrical connecting leads must correspond to the

relevant VDE and DIN regulations. Only use con-

necting leads with the code H 07 RN.

The type designation must be printed on the con-

necting lead by regulation.

AC motor

• The supply voltage must be 230 volt ~ / 50 Hz.

• Extension leads up to 20 m in length must have a

cross-section of 1.5 mm

. Extension leads whose

length is over 20 m must have a cross-section of

at least 2.5 mm

• The mains connection is fused with a 16 A slow-

blow fuse.

Please give the following information if you have any

enquiries.

• Kind of current

• Machine type label data

If your are sending back the motor, always send the

complete drive unit with the switch.

Observe the safety instructions!

The product meets the requirements of EN 61000-

3-11 and is subject to special connection conditions.

This means that use of the product at any freely se-

lectable connection point is not allowed.

Given unfavorable conditions in the power supply the

product can cause the voltage to uctuate temporar-

ily.

The product is intended solely for use at connection

points that

a) do not exceed a maximum permitted supply im-

pedance “Z”, or

b) have a continuous current-carrying capacity of the

mains of at least 100 A per phase.

As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to oper-

ate the product meets one of the two requirements,

a) or b), named above.

13. Disposal and recycling

The equipment is supplied in packaging to prevent

it from being damaged in transit. The raw materials

in this packaging can be reused or recycled. The

equipment and its accessories are made of various

types of material, such as metal and plastic. Defec-

tive components must be disposed of as special

waste. Ask your dealer or your local council.

14. Troubleshooting table

Warning: In the interests of operational safety, always switch off the saw and remove the mains plug before carrying out

maintenance work.

Problem Possible Cause Help

1. Saw blade gets

loose after turning

off the motor

Fastening nut tightened insufciently Tighten fastening nut, M20 left-handed thread

2. Motor does not start a) Failiure main fuse

b) Extension cable defect

c) Connections on the motor or switch defect

d) Motor or switch defect

a) Check the mains fuse.

b) Replace the extension cable

c) Have to checked by an electrician

d) Have to checked by an electrician

3. No motor output,

turns off automati-

cally

a) Cross section of extension cable is too low

b) Overload by dull saw blade

a) See "electric connection"

b) Insert a sharpened saw blade

4. Burns on the cutting

surface

a) Dull saw blade

b) Wrong saw blade

a) Insert a sharpened saw blade

b) Insert correct saw blade

/ 248

Bekijk gratis de handleiding van Toolson WS4100, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.