Handleiding
Je bekijkt pagina 8 van 29
10 11
MANUAL FUNCTIONS:
•
Pulse: Press the pulse button to
let the appliance run for only a
few seconds at a time. To stop it,
release the button. Press the
pulse button as often as it is necessary.
The longest working time can not be
more than 3 minutes.
•
Blend: select blend program on
screen then choose the speed
setting with + and – buttons,
validate with Start/Stop button.
Then choose timer, default time 2 min and
adjut with + and – buttons, validate with
Start/Stop button the programm will start
immediatly. At the end of the program, the
appliance bips 5 times.
•
Heat : allows to freely control the
way you want to heat. Press the
heat button, the screen indicates
« 75° » but you can choose the
heating temperature from 40° up to 100°
by selecting + and – buttons. Then press
Start/Stop button.
You can set up the working time by
selecting + and - buttons between
5
minutes and 90 minutes, the screen
indicate default time : 10 minutes. Then,
press Start/Stop button.
The remaining time appears on the screen.
Wait for the blender to stop automatically.
The appliance beeps 5 times. You can also
stop the blending during the cycle :
-
Within 1 minute of working, press the
start/stop button
-
More than 1 minute of working, press and
hold the start/stop button for 3 seconds.
•
Steam*: Add the ingredients in
the steam basket. Add 500ml of
water in the jar. Then add the
steam basket in the jar and close
the lid. Maintain heat /steam button for 2
seconds. The pictogram will become yellow
You can set up the working time by + and
-buttons, between 15 minutes and 60
minutes. Then press Start/Stop button. The
remaining time appears on the screen. Wait
for the blender to stop automatically, The
appliance bips 5 times. For safety reasons,
remove the cap and wait 1 minute to
remove excess steam.
*Depending on model
OTHER FUNCTIONS
•
Start/Stop : allows to stop any
blending or heating program
before the end by pressing this
button.You can also stop the
blending during the cycle :
- within 1 minute of working, press the
start/stop button
- more than 1 minute of working, press
and hold the start/stop button for 3 seconds
If the appliance switches off during
operation, proceed as follows :
-
Unplug and leave it to cool down for
approximately 15-20 minutes.
-
Reconnect the appliance to the power
supply and resume blending.
-
The appliance will keep the program in
memory for 3min if stopped.
•
You can use the brush to clean the
blade holder. Be careful, the blades
are very sharpened.
Caution:
•
Empty the preparation, the jug is
not meant for storing food in the
refrigerator or freezer.
•
To clean the outside of the motor
unit and the walls of the jug, use a
damp cloth.
•
Do not immerse the appliance in
water (neither the motor unit nor
the blade holder). Never put the
motor unit (D) under running water.
•
Refer to the cleaning table to check
how to clean each part.
•
Clean the jug immediately after use.
•
For easy cleaning, you can use. Deep
clean: Put 800ml of water in the
jug. Select the cleaning program
on the screen and press Start/Stop
button Wait for the end of program.
Finish cleaning the jug with the help of a
sponge.
•
Rinse the inside of the jug and the lid
under running water.
•
In the event of the heated part of the
jug getting extremely dirty, ll in the
jar with a mix of water and washing up
liquid and let it soaked for a few hours
to help get it clean.
•
Use a damp cloth to clean the motor
Unit. Dry it carefully.
CLEANING
WHAT TO DO IF YOUR APPLIANCE DOES NOT WORK ?
Problems Causes Solutions
Appliance does not work
The plug is not connected.
Connect the appliance to a
socket with the same voltage as
indicated on the rating plate of
the appliance.
The blender jug is not
positioned correctly on the
motor unit or the jug and lid are
correctly in place and are not
locked onto the motor unit.
Check that the blender jug and
the lid are positioned properly
on the motor unit as explained
in the instructions.
Appliance, keypboard or
program not responding
Unplug the appliance, wait for 1
minute and plug in again.
In case of overheating
Unplug and leave it to cool
down for approx.15-20 minutes.
The appliance stopped
while in use
Overload or overheating
Unplug and leave it to cool
down for approx.15-20 minutes.
Reconnect the appliance to
the power supply and resume
blending.
Excessive vibrations
The product is not placed on a
at surface.
Place the appliance on a at
surface.
Volume of ingredients is too
high.
Reduce the quantity of
ingredients processed.
Leak or overow from
the lid
Volume of ingredients is too
high.
Reduce the quantity of
ingredients processed.
The lid is not correctly
positioned.
Place the lid correctly on the
blender jug.
The seal of the lid is not
correctly positionned, or is
missed.
Put the seal in the correct
position.
Leak from the bottom of
the blender jug
Deterioration of the
watertightness of the appliance.
verify the blade holder is
correctly put in place and the
interface between blade holder
/ jug is totally clean.
If the problem persists, contact
the consumer service (see
contact information in the
warranty leaet)
EN
Bekijk gratis de handleiding van Tefal PerfectMix+ BL83SD, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Tefal |
| Model | PerfectMix+ BL83SD |
| Categorie | Blender |
| Taal | Nederlands |
| Grootte | 6872 MB |
Caratteristiche Prodotto
| Kleur van het product | Black, Stainless steel |
| Gewicht | 5800 g |
| Gewicht verpakking | 8000 g |
| Breedte verpakking | 257 mm |
| Diepte verpakking | 486 mm |
