Steinberg SBS-FZ 6000/5M handleiding
Handleiding
Je bekijkt pagina 7 van 25
12 13
Rev. 08.12.2020
Rev. 08.12.2020
ENEN
• REGULAR INSPECTIONS (recommended as monthly):
• Check chain wear and tear.
• Check the wear and tear of the hooks: level of wear and tear, damage, enlargement of the hook slit, shank bend
or hook deviation.
• Check fastening of the hooks.
• Clean and lubricate the chains.
POSSIBLE HAZARDS DURING USE
The hazards that can occur during use of the machine are mechanical hazards. The mechanical hazard occurs in situations in
which injuries can result from mechanical impact of various elements, e.g. machine parts, tools, etc. on people.
The basic mechanical hazards include squeezing, crushing, cutting, pulling in or catching; impact; puncture; abrasion; as well
as slipping and stumbling.
These hazards can occur both during normal machine operation and as a result of irregularities in machine operation. These
irregularities might result in machine failure.
The mechanical hazards can result from: moving machines, transported loads, moving elements, sharp/rough elements,
dropping elements/loads, slippery uneven surfaces, limited space, location of the work station in relation to the ground
(work at heights and in depths).
VII. CLEANING AND MAINTENANCE
The chain hoist must be cleaned regularly. After completion of work, remove all dirt from the chains and the machine itself.
The chains, hooks, hinges and hook latches must be regularly lubricated with grease. When the load chain is rusted, the
rust must be removed and the chain greased. If rust cannot be removed, the load chain must be replaced. All and any hoist
maintenance and inspection activities must be carried out by a trained and qualied employee. They cannot be conducted by
a person without proper experience and knowledge.
NOTE!
After 5 months of using the chain hoist (approximately if the hoist will be used more than 1500 times - 10 times daily), the
friction plates should be replaced.
Disassemble one by one the elements up to the element No. 22 (brake disc) inclusive - which should be replaced:
VIII. GENERAL MACHINE DIAGRAM
1 Gear housing 25 Cover nut 49 Screw
2 Transmission 26 Gear selector rack 50 Wheel
3 Shaft 27 Handle 51 6t hook lower frame
4 Spline gearwheel 28 Gear selector ratchet 52 Screw
5 Transmission mounting plate 29 Spring nest 53 Nut
6 Mounting hook 30 Gear selector spring 54 Washer
7 Mounting hook protection 31 Sleeve 55 6t arbor
8 Shaft for the Upper Hook 32 Wheel 56 Cover nut
9 Disc 33 Washer 57 Nut
10 Guide 34 Screw 58 Washer
11 Stripper 35 Pin 59 Wheel arbor
12 Side plate 36 Nut 60 9t hook x 2
13 Bearing load ring 37 Name plate 61 Protection clip
14 Hub 38 Rivet 62 9t hook upper frame
15 Spring 39 Washer 63 Screw
16 Spring ratchet 40 Screw 64 9t latch
17 Ratchet 41 Load chain 65 9t hook lower frame
18 Ring 42 Chain ring 66 Nut
10
24123
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
2122
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
46
47
59
58
57
56
55
54
53
60
61
65
64
63
62
61
60
66
67
68
69
70
46
47
48
49
50
51
52
46
35
36
34
33
32
31
27
26
24
23
22
21
20
18
19
25
28
29
30
40
39
38
37
Bekijk gratis de handleiding van Steinberg SBS-FZ 6000/5M, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Steinberg |
| Model | SBS-FZ 6000/5M |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6093 MB |
