Steinberg SBS-FZ 500/1,5M handleiding
Handleiding
Je bekijkt pagina 7 van 25
12 13
Rev. 08.12.2020
Rev. 08.12.2020
ENEN
• Check the chains - cleanliness, lubrication, twisting.
• Check the hooks: level of wear and tear, damage, enlargement of the hook slit, shank bend or hook deviation.
• REGULAR INSPECTIONS (recommended as monthly):
• Check chain wear and tear.
• Check the wear and tear of the hooks: level of wear and tear, damage, enlargement of the hook slit, shank bend
or hook deviation.
• Check fastening of the hooks.
• Clean and lubricate the chains.
POSSIBLE HAZARDS DURING USE
The hazards that can occur during use of the machine are mechanical hazards. The mechanical hazard occurs in situations in
which injuries can result from mechanical impact of various elements, e.g. machine parts, tools, etc. on people.
The basic mechanical hazards include squeezing, crushing, cutting, pulling in or catching; impact; puncture; abrasion; as well
as slipping and stumbling.
These hazards can occur both during normal machine operation and as a result of irregularities in machine operation. These
irregularities might result in machine failure.
The mechanical hazards can result from: moving machines, transported loads, moving elements, sharp/rough elements,
dropping elements/loads, slippery uneven surfaces, limited space, location of the work station in relation to the ground
(work at heights and in depths).
VII. CLEANING AND MAINTENANCE
The chain hoist must be cleaned regularly. After completion of work, remove all dirt from the chains and the machine itself.
The chains, hooks, hinges and hook latches must be regularly lubricated with grease. When the load chain is rusted, the
rust must be removed and the chain greased. If rust cannot be removed, the load chain must be replaced. All and any hoist
maintenance and inspection activities must be carried out by a trained and qualied employee. They cannot be conducted by
a person without proper experience and knowledge.
NOTE!
After 5 months of using the chain hoist (approximately if the hoist will be used more than 1500 times - 10 times daily), the
brake plates should be replaced:
Disassemble one by one the elements up to the element No. 22 (brake disc) inclusive - which should be replaced:
VIII. GENERAL MACHINE DIAGRAM
1 Transmission mounting plate 15 Brake plate 29 Handle
2 Transmission cover 16 Ratchet spring 30 Handle
3 Axis 17 Ratchet spring 31 Flywheel
4 Wheel 18 Ratchet 32 Gear selector lever
5 Ring 19 Ratchet washer 33 Spring
6 Rear cover with name plate 20 Spring 34 Wheel washer
7 Upper clamp 21 Hub 35 M8 nut
8 Upper hook clamp 22 Brake disk
9 Terminal ring 23 Ratchet wheel
10 Lower hook clamp 24 Hub spring
11 Arbor 27 Nut
12 Rivet 28 Hub suspension
13 Rivet 29 Hub arbor
14 Upper clamp 30 Chain gear wheel
15 Shaft arbor 31 Ring
16 Support 32 Roller
1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
11
14
22
278
27
27
34
35
33
32
30
27
26
23
21
15
17
19
20
31
29
28
27
25
22
22
24
Bekijk gratis de handleiding van Steinberg SBS-FZ 500/1,5M, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Steinberg |
| Model | SBS-FZ 500/1,5M |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4898 MB |
