Speed Queen TR7006BN handleiding
Handleiding
Je bekijkt pagina 7 van 12
of 827 kPa] static pressure measured at the faucet.
NOTE: Water pressure under 20 pounds per square
inch [138 kPa] will cause an extended fill time in the
washer.
Turn on the water supply faucets and flush the lines for ap-
proximately two minutes to remove any foreign materials that
could clog the screens in the water mixing valve. This is espe-
cially important when installing your washer in a newly con-
structed or renovated building. Build-up may have occurred
during construction.
Connecting Hoses
1. Remove the two plain rubber washers and two filter screens
from the accessories bag.
2. Install them into each end of the fill hoses as shown in
Figure
4
. The screen must be facing outward.
3. Screw hose couplings with the filter screens onto the water
faucets until they are finger-tight. Use the red color-coded
hose for the hot water connection and the blue color-coded
hose for the cold water connection.
4. Then, using a pliers, screw approximately 1/4 turn.
5. Screw hose couplings from other end of hoses onto the water
mixing valve until they are finger-tight. Make sure the red
color-coded hose from the hot water faucet goes to the water
mixing valve marked “H” and the blue color-coded hose
from the cold faucet goes to the valve marked “C”. Refer to
Figure
Figure 4
.
6. Then, using a pliers, screw approximately 1/4 turn.
IMPORTANT: DO NOT cross thread or overtighten
couplings. This will cause them to leak.
7. Turn water on and check for leaks.
8. If leaks are found, turn off the water, unscrew hoses and rein-
stall them until there are no leaks.
IMPORTANT: Turn off water supply whenever
there will be an extended period of non-use.
1. Filter Screen (Screen must be facing outward)
2. Fill Hose
3. Rubber Washer (Plain)
4. Cold Water Connection
5. Hot Water Connection
6. Install this end of hose to valve connections at rear of wash-
er.
7. Install this end of hose to water supply faucet.
8. Faucet
Figure 4
IMPORTANT:
Hoses and other rubber parts deteriorate after ex-
tended use. Hoses may develop cracks, blisters or
material wear from the temperature and constant
high pressure they are subjected to.
All hoses should be checked on a monthly basis for
any visible signs of deterioration. Any hose show-
ing the signs of deterioration listed above should be
replaced immediately. All hoses should be replaced
every five years.
Connect Drain Hose to Drain
Receptacle
1. Remove the drain hose from its shipping position on the rear
of the washer by unhooking the hose from the retainer
clamp.
2. Install the drain hose into the drain receptacle (standpipe, wall
or laundry tub) following the instructions below.
NOTE: Drain receptacle must be capable of han-
dling a minimum of 32 mm [1-1/4 inch] outside di-
ameter drain hose.
Standpipe Installation
1. Check standpipe height. The recommended height for the
standpipe is 914 mm [36 inches] . Standpipes higher than
1220 mm [4 feet] will result in slower draining and may ex-
tend cycle times.
Installation
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7 Part No. 204104ENR5
Bekijk gratis de handleiding van Speed Queen TR7006BN, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Speed Queen |
| Model | TR7006BN |
| Categorie | Wasmachine |
| Taal | Nederlands |
| Grootte | 1398 MB |
