Sony PDBK-202 handleiding
Handleiding
Je bekijkt pagina 16 van 60
16
Notes about i.LINK Connections (PDW-HR1 Only)
When the target device is an XDS Series
device
When you install this board in the XDS Series device, the
menu item 831 TS OUT AUDIO MODE and menu item
926 DVB-ASI SETTING are added to the setup menu
system of the device. Note that the menu item 036 is not
added.
For more information about the XDS Series device, refer
to “Setup Menu” in the Operation Manual supplied with
the device.
Notes about i.LINK
Connections (PDW-HR1
Only)
• Check that connectors are oriented properly before
connecting an i.LINK cable to your computer or to the
PDW-HR1. Trying to force an improperly oriented
connector may damage the connector or the PDW-HR1.
• Connect the i.LINK cable to your computer before
connecting it to the PDW-HR1. The PDW-HR1 may be
damaged by static electricity if you connect the cable to
the PDW-HR1 first.
• Before connecting or disconnecting an i.LINK cable
between the PDW-HR1 and other equipment with an
i.LINK connector, always power both the PDW-HR1
and the connected equipment off and disconnect all
power plugs from their power outlets.
Inserting or removing an i.LINK connector with the
power plugs still connected may cause a damaging surge
of high-voltage power to flow from the equipment’s
i.LINK connector into the PDW-HR1.
• A damaging surge of high-voltage power can still flow
into the PDW-HR1 from the i.LINK connector of
connected equipment even when a separate i.LINK cable
is connected to another i.LINK connector on the
equipment, for example when connecting a hard disk to
a computer with an i.LINK interface card that provided
multiple connectors.
Always power all equipment off and disconnect all
power plugs from their power outlets, both on the PDW-
HR1 and on the connected computer and its peripherals,
before connecting an i.LINK cable.
• Before turn on or off the power switch of the PDW-HR1,
always stop operation of all devices connected to the
PDW-HR1 over the i.LINK interface.
• If MPEG TS signal transmission is not possible with the
PDW-HR1 powered on, turn off the power switch of the
PDW-HR1 and then turn it on again.
926 12 PID(AUX1) Changes the AUX1 packet
PID value for DVB-ASI
output.
0815h
: Set PID value.
---: When sub item TS i.LINK
MODE of menu item 926
is set to “HDV”.
You can set the value over the
range from 0030h to 1FFEh
in 1h units (or 20h units,
when the SHIFT button is
held down).
Note
Do not set the same PID
value as other item.
13 PID(AUX2) Changes the AUX2 packet
PID value for DVB-ASI
output.
0811h
: Set PID value.
---: When sub item TS i.LINK
MODE of menu item 926
is set to “HDV”.
You can set the value over the
range from 0030h to 1FFEh
in 1h units (or 20h units,
when the SHIFT button is
held down).
Note
Do not set the same PID
value as other item.
Item
number
Item name Settings
Bekijk gratis de handleiding van Sony PDBK-202, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Sony |
| Model | PDBK-202 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 11278 MB |
Caratteristiche Prodotto
| Kleur van het product | Groen |
| Ondersteunde video-modi | 720p, 1080i, 1080p |
| Maximale videoresolutie | 1920 x 1080, - Pixels |
| Type converter | Actieve video-omzetter |
