Handleiding
Je bekijkt pagina 68 van 100
Adjusting the Height of the Stand (LMD-2451TD)
68
o SERIAL REMOTE connector (RJ-45)
Connect to the network or Sony BKM-15R Monitor
Control Unit by using a 10BASE-T/100BASE-TX LAN
cable (shielded type, optional).
For details, refer to the Interface Manual for
Programmers (saved in the supplied CD-ROM,
Japanese and English only.)
CAUTION
• When you connect the optional LAN cable of the unit
to peripheral device, use a shielded-type cable to
prevent malfunction due to radiation noise.
• For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
• The connection speed may be affected by the network
system. This unit does not guarantee the
communication speed or quality of 10BASE-T/
100BASE-TX.
ATTENTION
Par mesure de sécurité, ne raccordez pas le connecteur
pour le câblage de périphériques pouvant avoir une
tension excessive à ce port. Suivez les instructions pour
ce port.
VORSICHT
Aus Sicherheitsgründen nicht mit einem
Peripheriegerät-Anschluss verbinden, der zu starke
Spannung für diese Buchse haben könnte. Folgen Sie
den Anweisungen für diese Buchse.
p SERIAL REMOTE RS-232C connector (D-sub
9-pin, female)
Connect to the RS-232C control connector on external
equipment connected to the monitor. The monitor can
be operated according to control commands sent from
external equipment connected to it.
For details on the pin assignment and factory setting
function assigned to each pin, see page 92.
For details, refer to the Interface Manual for
Programmers (saved in the supplied CD-ROM,
Japanese and English only.)
q DVI-D input connector (DVI-D)
Inputs DVI Rev.1.0 applicable digital RGB signal.
To view the signals of the SXGA and higher resolution
when the DVI input is selected, use the cable within 3 m
(118
1
/8 inches) in length.
r HD15 input connector (D-sub 15-pin, female)
Inputs an analog RGB video signal (0.7 Vp-p, positive
polarity) and sync signal.
The Plug & Play function corresponds to DDC2B.
Adjusting the Height of
the Stand (LMD-2451TD)
LMD-2451TD comes equipped with a stand.
You can adjust the height of the monitor in three levels
by changing the position of the stand attachment bracket
and the arm attachment position. Depending on the
height, you can install the input adaptor with the stand
attached to the monitor.
A and B in the following list indicate the screw holes
shown in the illustrations in steps 2 and 4.
Height of the monitor
Unit: mm (inches)
1)
You can install the input adaptor with the stand attached to the
monitor.
2)
Default setting
3)
You cannot attach the stand in combinations of these positions.
1
Remove the stand attachment bracket (see
page 69).
2
Attach the stand attachment bracket to the A or B
screw holes.
The bracket is attached to the B holes at the factory.
3
Attach the stand attachment bracket with four
screws.
Use the screws removed in step 1.
Position of the
stand attachment
bracket
AA B B
Arm attachment
position
BA B A
LMD-2451TD –
3)
430.5
(17)
471.6
1)
(18
5
/8)
497.9
1), 2)
(19
5
/8)
+
–
A A
AA
BB
BB
AA
A: Screw holes for low position
B: Screw holes for high position
Bekijk gratis de handleiding van Sony LMD-2451TD, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Sony |
| Model | LMD-2451TD |
| Categorie | Monitor |
| Taal | Nederlands |
| Grootte | 20038 MB |
Caratteristiche Prodotto
| Kleur van het product | Zwart |
| LED-indicatoren | Stroom |
| Bluetooth | Nee |
| Aan/uitschakelaar | Ja |
| Beeldscherm | LCD |
