Sonifex HY-03 handleiding
Handleiding
Je bekijkt pagina 13 van 28
5
Introduction 1
Note: The remote lamp tally mimics the front panel line connect switch
lamp, i.e. it flashes when ringing and is on when the line is held.
The hybrid unit will now behave as a 4 wire to 2 wire converter with signal
inputs at the mic/line Input connector and telephone signal output at the
output connector.
The call may be cleared by repressing the line connect switch or by means
of the remote divert switch. The call can also be cleared automatically by
enabling either the K-break disconnect or the dial tone disconnect (using
the optional HY-03DTD dial tone disconnect plug-in PCB).
With both auto-answer and auto-clearance in use, call handling can be
completely automatic in operation.
Making a Call
To initiate a call, lift the handset and dial the required telephone number.
When the call has been established, press the line connect switch and the
call will be handed over to the telephone hybrid unit. To clear the line at the
end of the call, press the line connect switch. The line connect switch lamp
is off in the non-connected mode and illuminated in the connected mode.
FAQ (Frequently Asked Questions)
The answers to most of the following questions are available elsewhere in
the handbook, but have been summarised here for convenience.
Q: What are the remote connection details for these units ?
A: The remote connector is a 9-way female (socket) ‘D’ type. To remotely
divert, connect pin 1 to pin 2. Pin 3 supplies +15V with reference to pin 4.
The remotes can act as momentary or latching depending on the setting on
the rear panel of the unit:
Pin 1: Divert switch (Line Connect)
Pin 2: Common
Pin 3: Lamp
Pin 4: Common
Q: What type of remote lamp will the HY-03 drive?
A: The remote lamp type should be 15V at 40mA max. When connecting
any loads the current should be limited to this value using a series resistor.
For example a 390 ohm resistor would limit the current to 38mA.
To connect/disconnect the unit pins 1 and 2 should be connected
together via a contact closure or equivalent. Care should be taken that
pin 3 is not connected to pins 1 or 2 and that incompatible external
signals are not used. Incorrect configuration can result in the failure of the
connect/disconnect transistor and protection diode which leaves the unit
permanently latched in a connected state and therefore unusable.
As this fault is caused by using the unit outside of its recommended
operating conditions it will not be covered under warranty.
Q: What is the power consumption of the HY-03 telephone hybrid?
A: <6W for HY-03 and HY-03S.
Q: What functions are controlled by the configuration settings switches on
the rear panel of the HY-03 telephone hybrid?
A: SW1 – Dial Tone Disconnect Enable.
SW2 – K-Break Disconnect Enable.
SW3 – Input/Output Mix Enable.
SW4 – Ring Detector (Auto-Answer) Enable.
Q: The telephone hybrids don’t automatically disconnect on dial-tone.
Why not ?
A: Whilst the HY-03 does include K-break disconnection (for the UK)
and line polarity reversal (for the US), these do not use the dial tone to
disconnect. There is no dial tone disconnection unless the HY-03DTD dial
tone detect option has been added. If the HY-03DTD option has been added
and you still have this problem, then ensure that configuration switch SW1
is set to on. Also, ensure that the HY-03DTD option is of the correct type for
your network connection. See the Dial Tone Disconnect section later in this
handbook.
Bekijk gratis de handleiding van Sonifex HY-03, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Sonifex |
| Model | HY-03 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 4310 MB |
