Silvercrest 7.4 SHM A1 handleiding
Handleiding
Je bekijkt pagina 20 van 99
20 GB/IE
Note: Charge the battery if the suction becomes
noticeably weaker and the number of illuminated
LEDs in the LED charge indicator
3
decreases.
Using the product
Note: The suction opening must always be clear
and should not be clogged. Otherwise the motor
may overheat and become damaged.
Before using the product, ensure the HEPA filter
12
and the dust collector
5
are installed cor-
rectly. To do so, remove the dust collector
5
by
turning it anticlockwise and removing it (Fig. A/I).
Ensure that the HEPA filter
12
is correctly posi-
tioned in the dust collector
5
(Fig. A/II).
Afterwards, attach the dust collector
5
by
turning it clockwise until it audibly locks into
place (Fig. A/III).
If desired, attach the 2-in-1 nozzle
8
into the
suction opening. This is suitable for cleaning,
for example, lamps, keyboards, or air vents in
the centre consoles of cars.
Note: If you do not need the brush, push it
down until it locks into place in the appropriate
recess.
Switch the product on by holding the ON/OFF
button
2
for 3 seconds. The LEDs of the LED
charge indicator
3
light up.
Note: Push the ON/OFF button
2
briefly to
switch on the LED lights
7
. The LED lights
7
can only be switched on before the vacuum is
operated.
Note: The handle
1
can be rotated by 180°
to vacuum difficult-to-reach corners (Fig. B).
After use, press the ON/OFF button
2
again
to switch the product off. The LED lights
7
switch off.
Using attachments
10
,
11
:
The product has an inflation feature. The included
attachments
10
,
11
make it possible to use the mo-
tor’s exhaust air. This allows you to inflate balloons
or other inflatable toys, for example.
Insert the desired attachment
10
,
11
into the
exhaust opening
4
(Fig. C).
Switch the product on by holding the ON/OFF
button
2
for 3 seconds. The LEDs of the LED
charge indicator
3
light up.
Inflate the desired item.
After use, press the ON/OFF button
2
again
to switch the product off. The LED lights
7
switch off.
Remove the attachment
10
,
11
from the exhaust
opening
4
.
Cleaning and care
Do not use aggressive, chemical,
or abrasive cleaners. These can
corrode the surface of the prod
uct.
Do not wash the product with
water; it is not waterproof.
Emptying the dust collector
5
: remove the dust
collector
5
by turning it anticlockwise and re-
moving it (Fig. A/I). Remove the HEPA-Filter
12
.
After emptying the dust collector
5
reinstall the
HEPA filter
12
back into the dust collector
5
(fig. A/II). Afterwards, attach the dust collector
5
by turning it clockwise until it audibly locks
into place (Fig. A/III).
Clean the housing and the 2-in-1 nozzle
8
with
a dampened cloth. For stubborn soiling use a
mild detergent on the cloth.
Store the product in a dust-free and dry location.
Disposal
The packaging is made entirely of recyclable mate-
rials, which you may dispose of at local recycling
facilities.
b
a
Observe the marking of the packaging
materials for waste separation, which
are marked with abbreviations (a) and
numbers (b) with following meaning:
1–7: plastics/20–22: paper and fibre-
board/80–98: composite materials.
Bekijk gratis de handleiding van Silvercrest 7.4 SHM A1, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Silvercrest |
| Model | 7.4 SHM A1 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8834 MB |
