Scheppach HWW1400 handleiding
Handleiding
Je bekijkt pagina 22 van 228
www.scheppach.com
22
|
GB
Please provide the following information in the
event of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consumables.
Wear parts*: Seals, pre-lter
* Not necessarily included in the scope of delivery!
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page.
12. Transport
Use only the transport handle (2) for transporting the
device.
13. Storage
Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Cover the electrical tool in order to protect it from dust
and moisture.Store the operating manual with the elec-
trical tool.
14. Disposal and recycling
Notes for packaging
The packaging materials are recycla-
ble. Please dispose of packaging in
an environmentally friendly manner.
Notes on the electrical and electronic equipment
act [ElektroG]
Waste electrical and electronic equipment
does not belong in household waste, but must
be collected and disposed of separately!
• Used batteries or rechargeable batteries that are not
installed permanently in the old appliance must be
removed non-destructively before disposal. Their
disposal is regulated by the battery law.
• Owners or users of electrical and electronic devices
are legally obliged to return them after use.
Extension cables up tp 25m long must have a mini-
mum cross-section of 1.5 mm². Mains fuse protection
is 16 A maximum.
11. Cleaning and Maintenance
Attention!
Only carry out maintenance, cleaning and adjustment
work when the mains plug is pulled out. We recom-
mend that you clean the device directly after every use.
Clean the device at regular intervals using a damp
cloth and a little soft soap.
Do not use any cleaning products or solvents - they
could attack the plastic parts of the universal machine
stand. Make sure that no water can penetrate the de-
vice interior.
• The pump is largely maintenance-free. However, for
a long service life, we recommend regular checking
and care.
• Before extended periods of inactivity or through
the winter, the pump should be thoroughly ushed
through with water, emptied completely and then
stored dry.
• To empty the pump housing, loosen the water drain
screw (5) and tilt the pump slightly.
• If there is a risk of frost the pump must be completely
emptied.
• After longer periods of storage check the pump by
switching on/o briey in order to check that the ro-
tor turns normally.
• In the event of the pump being jammed connect the
pressure line to the water supply line and remove
the suction hose. Open the water supply line. Switch
the pump on for ca. two seconds several times. This
method recties blockages in most cases.
• To clean the pre-lter (9), unscrew the pre-lter cap
(8) and remove the lter unit. Clean the pre-lter with
warm water.
• The pressure in the pressure vessel should be ap-
prox. 1.5 bar max. If the air pressure is too low, it
should be increased again. To do this unscrew the
valve cover (10) on the container and add the miss-
ing pressure with a tyre inator gauge via the valve
(11). Then screw the valve cover back on.
Connections and repairs
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Bekijk gratis de handleiding van Scheppach HWW1400, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | HWW1400 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 30016 MB |
