Scheppach HS81S handleiding
Handleiding
Je bekijkt pagina 31 van 208
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB
|
31
Note: Tighten the nuts and bolts during assembly
only to the extent that they can not fall down.
If you tighten the nuts and bolts prior to nal assem-
bly, nal assembly can not be performed.
Mounting the bench extension (g. 3)
1. Turn the saw and place it on the oor with the
bench facing down.
2. Align the bench extension (8) ush with the saw
bench (1).
3. Push table extension (8) onto the sawing table (1)
using the hex bolts (20) and loosely fasten the hex
nuts (19). Repeat for the opposite side.
4. Screw the support struts (16) to the table exten-
sions (8) with the hex bolts (20) and the hex nuts
(19)
5. Subsequently, tighten all screws.
Mounting rack (g. 4-7)
1. Screw the four support legs (9) together with
the support struts (16) onto the saw with the hex
bolts (20) (g. 4). For this use the saw blade key
(15a/15b), part of the delivery contents (g. 4).
2. Now place the rubber feet (17) onto the support
legs (9) (g. 5).
3. Now, screw the long centre brace (22) and the
short centre brace (21) onto the legs (9) using the
hexagon head bolts (20) and the hexagon head
nuts (19). Make sure that the same braces face
each other. The long centre braces (22) must
be mounted parallel to the operator‘s side of
the saw. (Fig. 6).
4. Using two hex bolts (20) on each, loosely secure
the and hex nuts (19) at the drill holes of the rear
support legs of the support frame (18) (g. 7).
Attention!
Both support frames must be fastened to the
back of the machine!
5. Then, tighten all the nuts and bolts of the under-
frame.
Setting / mounting the riving knife (gs. 8-10)
m The setting Caution! Pull out the main plug!
The setting of the riving knife (6) must be checked
prior to commissioning of the riving knife (6)
must be checked prior to commissioning.
1. Set the saw blade (3) to the max. cutting depth,
bring it to the 0° position and lock it.
2. Unfasten the bolt (23) from the bench insert (2)
using a Phillips screwdriver, and remove bench
insert (22) (g. 8).
3. The distance between the saw blade (3) and the
riving knife (6) must be max. 5 mm. (Fig. 9)
4. Loosen the mounting bolt (24) in order to pull out
the splitting wedge (6) until the right distance is
adjusted (g. 10).
5. Tighten the mounting screw (24) again and mount
the bench insert (2).
Cutting height max. 45° 45 mm
height adjustment 0 - 70 mm
saw blade swivel 0 - 45°
suction port ø 40 mm
weight 14 kg
Noise values
The total noise values determined in accordance
with IEC 62841.
sound pressure level L
pA
99.6 dB(A)
uncertainty K
pA
3 dB
sound power level L
WA
112.6 dB(A)
uncertainty K
WA
3 dB
Wear hearing protection.
The eects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.
7. Before starting the equipment
• The equipment must be set up where it can stand
securely.
• All covers and safety devices have to be properly
tted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
• Before you press the ON/OFF switch check that the
saw blade is tted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power
supply make sure the data on the rating plate are
identical to the mains data.
• Connect the machine to a properly installed pro-
tective contact socket, with at least 16A circuit
breaker.
8. Construction
Important. Pull out the power plug before carry-
ing out any maintenance, resetting or assembly
work on the circular saw!
Place all parts supplied on a at surface. Grouping
equal parts.
Note: If compounds with a bolt (round head / or hexa-
gon), hex nuts and washers are backed up, the wash-
er must be tted under the nut.
Insert screws each from outside to inside. Secure
connections with nuts on the inside.
Bekijk gratis de handleiding van Scheppach HS81S, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | HS81S |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 35195 MB |
