Scheppach HBS25 SE handleiding
Handleiding
Je bekijkt pagina 30 van 56
7. After successful adjustment, close the housing doors
(11) again and secure the door locks (10). Use the
slotted screwdriver (A).
8.6 Adjusting the top band saw blade
guide (5) (Fig. 8)
Note:
Check the setting before every cutting process and adjust
if necessary.
1. Loosen the wing screw (18).
2. Lower the top band saw blade guide (5) as close as
possible (distance approx. 2-3 mm) to the workpiece
to be processed by turning the adjusting nut (18a).
3. Retighten the wing screw (18).
8.7 Adjusting the saw table (7) to 90°
(Fig. 9, 10)
1. Adjust the saw table (7) horizontal to 90°.
2. This setting is predefined by the end stop screw (31).
3. Check the end stop screw (31) and the counternut
(31a) for firm seating and tighten if necessary. Use the
open-ended spanner AF 10/13 (B).
4. If the saw table (7) is not adjusted at a right-angle to
the saw blade (17), the end stop screw (31) must be
readjusted.
5. Loosen the end stop screw (31) and the counternut
(31a). Use the open-ended spanner AF 10/13 (B).
6. Turn the end stop screw (31) clockwise to lower the
end stop point or anti-clockwise to increase it.
7. Using an angle*, align the saw table (7) at a right-an-
gle to the band saw blade (17), put the end stop screw
(31) in the desired position and tighten the counternut
(31a) again. Use the open-ended spanner AF 10/13
(B).
* = may not be included in the scope of delivery!
8.8 Use as a stationary machine (Fig.
1)
The product must be mounted on a workbench for contin-
uous use.
• The product must be securely installed, i.e. bolted
down on a workbench or fixed machine stand.
• There are fixing holes in the foot (9) for this purpose.
1. Mark the drill holes.
– Place the product as it will be installed later.
– Mark the positions of the holes to be drilled on the
workbench.
These are given by the holes in the foot (9).
We recommend installing close to the edge.
2. Drill the holes (at least 6.5 mm diameter) through the
workbench.
3. Place the product over the drilled holes congruent with
the holes in the foot (9) and insert suitable screws*
through the holes from above and tighten them.
* = may not be included in the scope of delivery!
8.9 Extraction port set (16) (Fig. 2)
The product is equipped with an extraction port.
The extraction port set (16) has a diameter of 40 mm.
Connect a dust extractor when processing dusty materi-
als.
ATTENTION
The dust extraction system must be suitable for the ma-
terial to be processed.
Use a special extraction device to extract particularly
harmful or carcinogenic dusts.
1. Connect the hose of a suitable dust extraction sys-
tem* (e.g. industrial hoover) directly to the extraction
port set (16).
* = may not be included in the scope of delivery!
8.10 Push rod retainer (32) (Fig. 11)
The push rod retainer (32) is pre-mounted on the frame
(14).
If unused, the push rod (21) must always be stowed in the
push stick retainer (32).
9 Operation
ATTENTION
Always make sure the product is fully assembled
before commissioning!
Note:
The product is equipped with a safety switch. This means
that the product cannot be switched on if the doors are
open or have not been closed properly.
Make sure that both safety switches (11a) engage proper-
ly on the housing doors (11).
WARNING
Danger of injury!
The on/off switch and the safety switch must not be
locked!
– Do not work with the product if the switches are
damaged.
– Make sure the product is in working order before
each use.
WARNING
Always make sure that the tool attachment is fitted cor-
rectly!
WARNING
Make sure that the tool attachment is suitable for the
material to be processed.
Note:
The product must be mounted on a workbench for contin-
uous use.
• Let the tool attachment reach full speed before
processing the workpiece.
• Select a tool attachment that corresponds to the mate-
rial to be processed.
• The saw table must be mounted correctly.
30 | GB www.scheppach.com
Bekijk gratis de handleiding van Scheppach HBS25 SE, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | HBS25 SE |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 8367 MB |
