Scheppach GP1100 handleiding
Handleiding
Je bekijkt pagina 23 van 40
www.scheppach.com
GB
|
23
Cover the electric tool to protect it from dust or mois-
ture.
Store the operating manual with the power tool.
13. Electrical connection
The electrical motor installed is connected and ready
for operation. The connection complies with the appli-
cable VDE and DIN provisions. The customer‘s mains
connection as well as the extension cable used must
also comply with these regulations.
13.1 Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Pressure points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been improp-
erly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the wall
outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Ensure that the connection cables are dis-
connected from electrical power when checking for
damage.
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions. Only use connection
cables of the same designation.
The printing of the type designation on the connection
cable is mandatory.
If the mains connection cable of this device is dam-
aged, it must be replaced by a special connection ca-
ble which can be obtained from the manufacturer or its
service department.
AC motor 230 V~ / 50 Hz
Mains voltage 230 V~ / 50 Hz.
Mains power connection and extension leads must be
3-core = P + N + SL. - (1/N/PE).
Extension leads up to 25 m must have a minimum
cross-section of 1.5 mm². The mains power connection
must be protected with a max. 16 A fuse.
Clean the product at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic parts
of the product.
• We recommend regular inspections and care for a
long service life (i.e. At least once a month).
• Before extended periods of inactivity or through
the winter, the garden pump should be thoroughly
ushed through with water, emptied completely and
then stored dry.
• To empty the housing, loosen the drain screw (4)
and tilt the garden pump slightly.
• If there is a risk of frost the garden pump must be
emptied.
• After longer periods of storage check the pump by
switching on/off briey in order to check that the ro-
tor turns normally.
• In the event of the garden pump being jammed con-
nect the pressure line to the water supply line and
remove the suction line. Open the water supply line.
Switch the garden pump on for ca. two seconds sev-
eral times. This method recties blockages in most
cases.
Connections and repairs
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Service information
With this product, it is necessary to note that the follow-
ing parts are subject to natural or usage-related wear,
or that the following parts are required as consuma-
bles.
Wearing parts*: Seals, pre-lter, ow sensor wheel,
non-return valve
* may not be included in the scope of supply!
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page.
12. Storage
Store the device and its accessories in a dark, dry and
frost-free place that is inaccessible to children.
The optimum storage temperature lies between 5 and
30 ˚C.
Store the power tool in its original packaging.
Bekijk gratis de handleiding van Scheppach GP1100, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | GP1100 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 5147 MB |
