Scheppach DWS9 handleiding
Handleiding
Je bekijkt pagina 25 van 72
www.scheppach.com
GB
|
25
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: carbon brushes, grinding wheel, brush
head, sand paper
* not necessarily included in the scope of delivery!
Spare parts and accessories can be obtained from
our service centre. To do this, scan the QR code on
the cover page.
10. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions.
The customer‘s mains connection as well as
the extension cable used must also comply with
these regulations.
Important information
In the event of an overloading the motor will switch
itself o. After a cool-down period (time varies) the
motor can be switched back on again.
Damaged electrical connection cable.
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking „H05VV-F“.
The printing of the type designation on the connec-
tion cable is mandatory.
AC motor:
• The mains voltage must be 220 - 240 V~.
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm
2
.
4. Hold the grinding plate (9) as parallel as possi-
ble to the wall, and touch the surface to be pro-
cessed with the brush edge (10) rst.
5. Apply some pressure to the grinding head (8)
such that the insertion tool touches the surface
to be processed.
6. Constantly move the power tool over the surface.
Note: lf you want to avoid irregular grinding results,
do not keep the power tool at one spot for too long.
7. Lift the grinding plate (9) from the surface to be
processed before switching o the power tool.
8. Do not put aside the power tool until the insertion
tool has come to a complete halt.
After use
1. Switch o the power tool as described, discon-
nect it from the power supply and Iet it cool down.
2. Clean and maintain the power tool as described
below, and store it carefully.
9. Cleaning, maintenance and repair
WARNING! Unplug the power tool before starting
to work on it (e.g. transport, installation, retrot-
ting, cleaning and maintenance)!
Cleaning
a) Keep protective devices, ventilation openings and
motor housings free from dust and dirt as far as
possible.
b) Wipe the power tool with a clean cloth or remove
dust and dirt with compressed air at low pressure
(max. 3 bar).
c) Clean the power tool immediately after each use.
d) Do not use any detergents or solvents as they
may aect the plastic parts of the power tool.
Make sure to avoid any water ingress into the
tool.
Replacing the power supply line
lf the power supply line of this power tool is dam-
aged, it must be replaced by the manufacturer or the
customer service or any equally qualied person in
order to avoid risks.
Maintenance
Check the power tool and accessory parts (e.g. in-
sertion tools) for wear and damage before and af-
ter each operation. lf necessary, replace worn out
or damaged parts with new parts and make sure to
comply with the operating instructions.
Observe any technical requirements.
Grinding plate, brush edge
Have a qualied specialist replace damaged or worn
out grinding plates (9) and brush edges (10) with new
ones of the same type.
Bekijk gratis de handleiding van Scheppach DWS9, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | DWS9 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 11265 MB |
