Scheppach DS210 handleiding
Handleiding
Je bekijkt pagina 23 van 116
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB
|
23
In doing so, ensure that you move the sander evenly
and over a wide area, if you stop the sander on the
work surface or move the sander unevenly, this may
result in a disagreeable spiral pattern of scratches
and an uneven work surface. The sanding disc can
be re placed if it is damaged or severely abraded.
c) Triangular sanding head
The triangular sanding head does not rotate, but vi-
brate.
8. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions. The
customer‘s mains connection as well as the ex-
tension cable used must also comply with these
regulations.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking „H05VV-F“.
The printing of the type designation on the connec-
tion cable is mandatory.
AC motor
• The mains voltage must be 220 - 240 V~ 50 Hz.
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm
2
.
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Preselecting the speed (Fig. 5)
To select the operating speed, move the dial to
the required value. Stage 1 indicates the minimum
speed. Stage 5 indicates the maximum speed.
Switching on and o (Fig. 6)
The switch of the machine is two step switch. As
shown in following picture,
1. Press the rear end of the switch and push the
switch forward to power on
2. Press the front end of the switch down to lock the
switch in on“position
3. Press the rear end of the switch to power o.
7. Working with the power tool
Always hold the wall sander with both hands! Keep
your hands away from the sanding head. Otherwise,
your hand could become caught, as the sanding
head swivels in dierent directions.
1. Attach sanding head.
2. Attach sanding tool.
3. Connect dust extraction system.
4. Insert mains plug.
5. Switch on dust extraction system.
6. Switch on the device.
7. Grip the wall sander by both handles. Press the
wall sander gently against work surface (the
pressure should be just enough to ensure that
the sanding head is ush with the work surface).
Sanding head operation instruction
a) Brushing ring
A brush type rim surrounds the round sanding head.
This time has two functions:
As the ring projects above the surface of the sanding
plate , it is the ring which comes into contact with the
work surface rst. As a result the sanding head is
brought parallel to the work surface before the and-
ing tool comes into contact with the work surface.
This avoids a sickle-shaped depression ca used by
the edge of the sanding disc.
The ring also retains the dust until it is extracted by
the dust extractor. If the brush ring is damaged or
shows excessive wear, it should be replaced.
b) Round sanding head
When working on the round sanding head, apply only
as much pressure as is required to keep the sand-
ing tool in contact with the work surface. Excessive
pressure may result in a disagreeable spiral pattern
of scratches and an uneven work surface. Move the
sander constantly while the sanding tool is in contact
with the work surface.
Bekijk gratis de handleiding van Scheppach DS210, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Scheppach |
| Model | DS210 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 18622 MB |
