Handleiding
Je bekijkt pagina 3 van 11
Pre-wire
or
Pre-constructi
on
locati:-
au
obstrvctions
tAC
ng, plumbing. duct
work.
studs. and
Joists!.
Route the speakel wire
to~
speaker
locat10n avoiding all obstacles. Wiltch
outfardoseness
to~
11119,
Rmsoond
olfen
Speaka
Rough-In 8fad<!ts lhat
can
be fastened to
:ne
adiaa,nt
5UJCh.
Ona
lhe
dry
w.a
Is
inslalled. lhe opening
is
OJI
out. There
are
holes molded Into the bfad<et
for
s,x-der wue
~
to
lttp
the wire from
being
lost during construcuon
Makl!sure
thu~aw
cutout fhok!)doesn'textemlfurthet than l/4"{0.6cml
from the Inside
of
he mounung bracket.
In-celling bracket
Ins
tallation
-
In-wall bracket Installation
Retrofit lnstallatlon
----
Rough-in Bracket
Stud/
Joist
•-screw
Note:
Run
two pair conductors for
single point speakers.
Magnetic square grille
ICG-6S
(6"
Models) and
ICG
-85 (8"models}
(sold separately)
locate exlstlng
plpei.
duct wotk, and
AC
wiring before cutting any holes
in
the~ing.
Center
the
cardboard template between adjacent joists.
aYOiding
all
wlrlng.plpes,duc;twork, and 6ghilymart theoutfinewtth.i pencil
TlK-n
use
a
kryflolc!/dryw311
saw
or
motorizl!d sp,ral-oJt
!CIOI
ICI
ma
lhcope
·ng.
2.
Score
the
ouUine
of
the
template with a utility
km.le
ID
~t
chipping.
If
dN!ing with
bih
and plaster
Of
tluck paneling.
dnD
1 •
(2.5 anl holes
In
several
~
around !he
pend
outline. Use a
fin
ICIOthed
ki:yhole
saw
or
tlildsaN
blade
with
slow
strokes
to
saw
throu9h and
lef!)OVI!
the
inner surface.
Score template outfine
Cut
out opening
Retrofit Installation
PREPARATION / SPEAKER PLACEMENT
Additional
Ti
ps
/ Considera
ti
ons
Try
10
run speaker wires alter
AC
wiring
is
In
so you can separate the
wires,
avold,ng
Induced
llOISe
oused
by
dose
parallel posruon,ng
or
the
rwo
Wlft!I~
Secure
~aker
res m place against a stud along vertical runs. Do
no1
pierce
&he
lnw!itlon.
Allow
a bit
o(
sladt
for
expans,on
of
building
~1erlals.
Route horizontal Wll'I! runs th,ough holesdn11ed
In
studs at
roughly~
heights.
Spea~
Jhould not
be
Installed
untJI
the wallboard
Is
In
place.
In
the
meantime, leave
~eral
reet
of
w,re coiled up and secured to the
bac
51d
of lh" mounting
fral'l"e.
Excess
length
an
be
remo,,ed dunr,g linal
assembly.
Whe11
ln\lalllng the
dl)IW311.
make
sure
the
speaker cutout hole doesn't
extend farther than
1/4"
(0.6
cm)
from the inside of the mounttng frame.
Sp<?aker-.
installed
In
ceillngs should have a safety wire tied between
the back
of
the 1peaker and the frame
of
the
building.
Use
any strong
ln5-Ulated
wire.connect
itto
the speakerhame or baffle so
It
doesn't
lnterf-wlth
the speaker's operation. The other end should be
firmly
attadll!d to the }oist or flooring above
USing
a hook.
nalL
or other reliable
fas1ener.
Tenn1mtlng the wires
man
outlet box
amched
10
a stud or
rl!trofrt
junctlQ(l boll
at
thl! e,at lOcalJOn. U5e an outlet pl,Jte with spcakef wire
terminations.
After
the
drywall
is-,ued
and fini!hed, lnst;ill the !.peal«!n as wf!ve
dCKrlbed
P
ai
nting the Speaker Gril
le
Runound Atchllectural
Speaker
Grilles have
-a
design« white finl\h that
Clln
be
painted
with
Oltlinary latex paint Remove the
speakef
gnlle from the
Speilkl'r before painting_
1.
Remove
the magneoc speaker
grHle
and carefully remove the
sc
rim cloth
from the grille and set
aside.
2.
Paint the
grille.
Russound recommends diluting the
latt>X
paint with
Will~
4:1
or
S:1
proporuonally. Due to the
fine
mesh openings, using
several
layer~
of
• thinner paint
Sj)lily
is
reconvnended rather than
ining
a single,
thidc.er
coat.
A thick coat
Is
likely
lo
dog
the
speaker
grille
open,~
3
While
the pa,nt
is
st
wet
on
the
grille. and w grille
Is
not
anacht-d to ttte
Framt-.
use a gentle burst
of
compressed air aga,nrt
thl!
ou~
Mface
to clear
lhe line holes
in
the
me:sll.
4 Altef the paint has thotoughly dried, re-attach the
scr
m
doth.and
1tt«h
the
gr
ID
the
frame_
Speaker
Assembly
Do
not attach
the
grille until
the
speaker
hos
been
connected
and
secured
in
the
ceiling.
-speaker
- Scrim Cloth
-Grille
Ru
ssound Architectural Series
of
In-Ceiling and In-Wall Loudspeakers 3
Bekijk gratis de handleiding van Russound IC-820T, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Russound |
| Model | IC-820T |
| Categorie | Speaker |
| Taal | Nederlands |
| Grootte | 12508 MB |
